Hydraulic Flanges and components

- ISO 6162-1 and 2 /SAE rectangular flanges
- CETOP ou SID./ ISO 6164 square flanges

Principe :
This is based on inserting a compressible seal between 2 faces arranged parallel to one another, and tightly held, pressing against one another be means of bolted flanges.
The seal is exactly centred by means of a circular groove in which it is housed.
For union assembly flanges, the two faces will be flanged head end (one with a seal, the other without).
For port assembly flanges, the two faces will be on one hand the flanged head en holding the seal, and on the other the external part of the hydraulic appliance to be seal (motor, pump, jack etc...)

Advantages of using S.A.E. flanges:
- Connection capacity of tubes up to 5" external diameter (ISO 6162-1, SAE J518 code).
- For tightening the screws, slightly lower tightening torques compared with the equivalent connection threads are required.
- Low tightening torques also mean using small flat wrenches, ensuring better performance where the installation space is tight.
- Application up to 420 bars (6000 PSI) for flange sizes 1/2" to 2" (ISO 6162-2, SAE J518 code 62).
- Just one sealing point between fitting the tube/ pipe to the flanged joint.
- Easy to remove thanks to the use of split flange clamps.

Material

- Rectangular flanges one piece or two part : Wrought steel S 355** ( E 36-3 / St 52-3 ) on request stainless steel AISI 316
- Square flanges CETOP and Sid. : S 355** steel on request stainless steel 304L ( 1.4306 ) or 316L ( 1.4306 )
- ISO / SAE Blocks : C35/C45 steel ( XC38/48 – CK35/45 ) on request stainless steel 304L ( 1.4306 ) or 316L ( 1.4306 )
- Flanged head to be welded : S 235** steel ( E24 / St 37 ) on request stainless steel 304L ( 1.4306 ) or 316L ( 1.4306 )
- Standard 0"Rings : Perbunan / Viton* 90 Shore A
- Flange plugs and Threaded flanged head : S 235** steel ( E24 / St 37 ) on request stainless steel 304L ( 1.4306 ) or 316L ( 1.4306 )
- Métric / UNC CHC bolts : Class 12.9 quenched steel
- Nuts : Class 10 quenched steel

Normalizations

Flange types

Machining

Protection

Tightening torque

Sealing

Rectangular flanges - SAE 3000 / SAE 6000

Flasques

FLANGES SAE 3000 / SAE 6000

FLANGES ACCORDING TO THE ISO 6162-1 / SAE 3000
Part N°	PN bar¹	DN	F	Ø D	Ø J	U	Ø T	GG	Q	FF	O	Bolts
Part N°	PN bar¹	DN	F	Ø D	Ø J	U	Ø T	GG	Q	FF	O	Metric	UNC
BM-3000-3/8"-M	350	10	6.2	24.9	18.7	14	8.7	16.5	35	40	50	8	-
BM-3000-1/2"-M/U	350	13	6.2	31	24.3	13	8.7	17.5	38.1	46	4	8	5/16"
BM-3000-3/4"-M/U	350	19	6.2	38.9	32.2	14	10.5	22.3	47.6	52	65	10	3/8"
BM-3000-1"-M/U	315	25	7.5	45.3	38.5	16	10.5	26.2	52.4	59	70	10	3/8"
BM-3000-1"1/4-U	250	32	7.5	51.6	43.7	14	12	30.2	58.7	73	79.5	-	7/16"
BM-3000-1"1/4-M	250	32	7.5	51.6	43.7	14	12.5	30.2	58.7	73	79.5	12	-
BM-3000-1"1/4"-M/ISO*	250	32	7.5	51.6	43.7	14	10.5	30.2	58.7	73	79.5	10	-
BM-3000-1"1/2-U/ISO*	200	38	7.5	61.1	50.8	16	13.5	35.7	69.8	83	94	12	1/2"
BM-3000-1"1/2-M	200	38	7.5	61.1	50.8	16	14.5	35.7	69.8	83	94	14	-
BM-3000-2"-U/ISO*	200	51	9	72.3	62.8	16	13.5	42.9	77.8	97	102	12	1/2"
BM-3000-2"-M	200	51	9	72.3	62.8	16	14.5	42.9	77.8	97	102	14	-
BM-3000-2"1/2-U/ISO*	160	64	9	84.9	74.9	19	13.5	50.8	88.9	109	114.5	12	1/2"
BM-3000-2"1/2-M	160	64	9	84.9	74.9	19	14.5	50.8	88.9	109	114.5	14	-
BM-3000-3"-M/U	138	76	9	102.4	90.9	22	17	61.9	106.4	131	135	16	5/8"
BM-3000-3"1/2-M/U	35	89	10.7	115.1	102.4	22	17	69.8	120.7	140	152	16	5/8"
BM-3000-4"-M/U	35	102	10.7	127.8	115	25	17	77.8	130.2	152	162	16	5/8"
(1)Pressure max. recommended Some flanges may equally well take metric bold and UNC bolts ; in this case reference numbers end with M/U or U/ISO, certain others can only take metric or UNC bolts ; in this case reference numbers end with M or U respectively. * according to the ISO 6162-1 norm (bolts diameters are different)

FLANGES ACCORDING TO THE ISO 6162-2 / SAE 6000
Part N°	PN bar¹	DN	F	Ø D	Ø J	U	Ø T	GG	Q	FF	O	Bolts
Part N°	PN bar¹	DN	F	Ø D	Ø J	U	Ø T	GG	Q	FF	O	Metric	UNC
BM-6000-1/2"-M/U	400	13	7.2	32.5	24.6	16	8.7	18.2	40.5	48	56.5	8
BM-6000-3/4"-M/U	400	19	8.2	42	32.5	19	10.5	23.8	50.8	60	71	10	5/16" 3/8"
BM-6000-1"-U	400	25	9	48.4	38.8	24	12	27.8	57.2	70	81	-	7/16"
BM-6000-1"-M	400	25	9	48.4	38.8	24	13	27.8	57.2	70	81	12	-
BM-6000-1"1/4-U / ISO*	400	32	9.8	54.8	44.5	27	13.5	31.8	66.6	78	95	12	1/2"
BM-6000-1"1/4/M	400	32	9.8	54.8	44.5	27	15	31.8	66.6	78	95	14	-
BM-6000-1"1/2-M/U	400	38	12	64.3	51.6	30	17	36.5	79.3	95	113	16	5/8"
BM-6000-2"-M / U / ISO	400	51	12	80.2	67.6	37	21	44.5	96.8	114	133	20	3/4"
(1)Pressure max. recommended Some flanges may equally well take metric bold and UNC bolts ; in this case reference numbers end with M/U or U/ISO, certain others can only take metric or UNC bolts ; in this case reference numbers end with M or U respectively. * according to the ISO 6162-1 norm (bolts diameters are different)

SPLIT FLANGES SAE 3000 / SAE 6000

SPLIT FLANGES ACCORDING TO THE ISO 6162-1 / SAE 3000
Part N°	PN bar¹	DN	F	Ø D	Ø J	U	Ø T	GG/2	Q	FF/2	O	Bolts
Part N°	PN bar¹	DN	F	Ø D	Ø J	U	Ø T	GG/2	Q	FF/2	O	Metric	UNC
DB-3000-1/2"-M/U	350	13	6.2	31	24.3	13	8.7	8.75	38.1	22.8	54	8	5/16"
DB-3000-3/4"-M/U	350	19	6.2	38.9	32.2	14	10.5	11.15	47.6	25.9	65	10	3/8"
DB-3000-1"-M/U	315	25	7.5	45.3	38.5	16	10.5	13.1	52.4	29.2	70	10	3/8"
DB-3000-1"1/4-U	250	32	7.5	51.6	43.7	14	12	15.1	58.7	36.3	79.5	-	7/16"
DB-3000-1"1/4-M	250	32	7.5	51.6	43.7	14	12.5	15.1	58.7	36.3	79.5	12	-
DB-3000-1"1/4"/ISO*	250	32	7.5	51.6	43.7	14	10.5	15.1	58.7	36.3	79.5	10	-
DB-3000-1"1/2-U/ISO*	200	38	7.5	61.1	50.8	16	13.5	17.85	69.8	41.1	94	12	1/2"
DB-3000-1"1/2-M	200	38	7.5	61.1	50.8	16	14.5	17.85	69.8	41.1	94	14	-
DB-3000-2"-U/ISO*	200	51	9	72.3	62.8	16	13.5	21.45	77.8	48.2	102	12	1/2"
DB-3000-2"-M	200	51	9	72.3	62.8	16	14.5	21.45	77.8	48.2	102	14	-
DB-3000-2"1/2-U/ISO*	160	64	9	84.9	74.9	19	13.5	25.4	88.9	54.1	114.5	12	1/2"
DB-3000-2"1/2/M	160	64	9	84.9	74.9	19	14.5	25.4	88.9	51.4	114.5	14	-
DB-3000-3"-M/U	138	76	9	102.4	90.9	22	17	30.95	106.4	65.3	135	16	5/8"
DB-3000-3"1/2-M/U	35	89	10.7	115.1	102.4	22	17	34.95	120.7	69.6	152	16	5/8"
DB-3000-4"-M/U	35	102	10.7	127.8	115	25	17	38.9	130.2	75.9	162	16	5/8"
(1)Pressure max. recommended Some flanges may equally well take metric bold and UNC bolts ; in this case reference numbers end with M/U or U/ISO, certain others can only take metric or UNC bolts ; in this case reference numbers end with M or U respectively. * according to the ISO 6162-1 norm (bolts diameters are different)

SPLIT FLANGES ACCORDING TO THE ISO 6162-2 / SAE 6000
Part N°	PN bar¹	DN	F	Ø D	Ø J	U	Ø T	GG/2	Q	FF/2	O	Bolts
Part N°	PN bar¹	DN	F	Ø D	Ø J	U	Ø T	GG/2	Q	FF/2	O	Metric	UNC
DB-6000-1/2"-M/U	400	13	7.2	32.5	24.6	16	8.7	9.1	40.5	23.6	56.5	8	5/16"
DB-6000-3/4"-M/U	400	19	8.2	42	32.5	19	10.5	11.9	50.8	30	71	10	3/8"
DB-6000-1"-U	400	25	9	48.4	38.8	24	12	13.85	57.1	34.8	81	-	7/16"
DB-6000-1"-M	400	25	9	48.4	38.8	24	13	13.85	57.1	34.8	81	12	-
DB-6000-1"1/4-U / ISO*	400	32	9.8	54.8	44.5	27	13.5	15.85	66.7	38.6	95	12	1/2"
DB-6000-1"1/4-M	400	32	9.8	54.8	44.5	27	15	15.85	66.7	38.6	95	14	-
DB-6000-1"1/2-M/U	400	38	12	64.3	51.6	30	17	18.25	79.4	47.5	113	16	5/8"
DB-6000-2"-M / U / ISO	400	51	12	80.2	67.6	37	21	22.2	96.8	56.9	133	20	3/4"
(1)Pressure max. recommended Some flanges may equally well take metric bold and UNC bolts ; in this case reference numbers end with M/U or U/ISO, certain others can only take metric or UNC bolts ; in this case reference numbers end with M or U respectively. * according to the ISO 6162-1 norm (bolts diameters are different)

Port assembly

PORT ASSEMBLY FLANGES - SAE 3000 / SAE 6000

BRIDES DE FIXATION BWI A PASSAGE INTEGRAL

PORT ASSEMBLY FLANGES BWI S.A.E. 3000 / ISO 6162-1
Part N°	PN bar¹	DN	For tube Diameter to…at…	Ø A	Ø H1	L	FF	O	GG	Q	Bolts
Part N°	PN bar¹	DN	For tube Diameter to…at…	Ø A	Ø H1	L	FF	O	GG	Q	Metric	UNC
BFX-3000-BWI-3/8	350	10	14-18	12	18	40	40	50	16.5	35	M 8X30
BFX-3000-BWI-1/2	350	13	18-22	13	22	45	46	54	17.5	38.1	M 8X25	5/16-11/4
BFX-3000-BWI-3/4	350	19	25-28	19	28	50	52	65	22.3	47.6	M 10X30	3/8-11/4
BFX-3000-BWI-1	315	25	30-35	25	35	55	59	70	26.2	52.4	M 10X30	3/8-11/4
BFX-3000-BWI-11/4 *	250	32	38-43	32	43	60	73	79.5	30.2	58.7	M 12X30*	7/16-11/2
BFX-3000-BWI-11/2 *	210	38	48-50	38	50	65	83	94	35.7	69.8	M 14X35*	1/2-11/2
BFX-3000-BWI-2 *	210	51	60-63	47	61.8	70	97	102	42.9	77.8	M 14X35*	1/2-11/2
BFX-3000-BWI-2 *	160	51	60-63	47	61.8	70	97	102	42.9	77.8	M 14X35*	1/2-11/2
BFX-3000-BWI-21/2 *	160	64	73-76	58	74	75	109	114.5	50.8	88.9	M 14X40*	1/2-13/4
BFX-3000-BWI-3	138	76	88-90	70	90	85	131	135	61.9	106.4	M 16X50	5/8-13/4
BFX-3000-BWI-31/2	35	89	95-102	86	102	90	140	152	69.8	120.7	M 16X50	5/8-2
BFX-3000-BWI-4	35	102	113-120	96	114	100	152	162	77.8	130.2	M 16X50	5/8-2
(1)Pressure max. recommended Flanges with 0'Ring and bolts. For metric bolts, add "M" after the reference ; for UNC bolts, add "U". Standard delivered with undivided split flanges, specify for split flanges. On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

PORT ASSEMBLY FLANGES BWI S.A.E. 6000 / ISO 6162-2
Part N°	PN bar¹	DN	For tube Diameter to…at…	Ø A	Ø H1	L	FF	O	GG	Q	Bolts
Part N°	PN bar¹	DN	For tube Diameter to…at…	Ø A	Ø H1	L	FF	O	GG	Q	Metric	UNC
BFX-6000-BWI-1/2	400	13	20-22	13	22	45	48	56.5	18.2	40.5	M 8X30	5/16-11/4
BFX-6000-BWI-3/4	400	19	25-28	17.5	28	50	60	71	23.8	50.8	M 10X35	3/8-11/2
BFX-6000-BWI-1	400	25	30-35	22	35	55	70	81	27.8	57.2	M 12X45	7/16-13/4
BFX-6000-BWI-11/4*	400	32	38-43	29	43.8	60	78	95	31.8	66.6	M 14X50*	1/2-13/4
BFX-6000-BWI-11/2	400	38	48-52	35	50.6	65	95	113	36.5	79.3	M 16X55	5/8-21/4
BFX-6000-BWI-2	400	51	60-65	43	65	70	114	133	44.5	96.8	M 20X70	3/4-23/4
1)Pressure max. recommended Flanges with 0'Ring and bolts. For metric bolts, add "M" after the reference ; for UNC bolts, add "U". Standard delivered with undivided split flanges, specify for split flanges. On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

PORT ASSEMBLY FLANGE REDUCING - SAE 3000 / SAE 6000

PORT ASSEMBLY FLANGES BWR REDUCING S.A.E. 3000 / ISO 6162-1
Part N°	PN bar¹	DN	For tube Diameter to…at…	Ø A	Ø H1	L	FF	O	GG	Q	Bolts
Part N°	PN bar¹	DN	For tube Diameter to…at…	Ø A	Ø H1	L	FF	O	GG	Q	Metric	UNC
BFX-3000-BWR-1/2	350	13	16-18	12	18	45	46	54	17.5	38.1	M 8X25	5/16-11/4
BFX-3000-BWR-3/4	350	19	18-22	13	22	50	52	65	22.3	47.6	M 10X30	3/8-11/4
BFX-3000-BWR-1	315	25	25-28	19	28	55	59	70	26.2	52.4	M 10X30	3/8-11/4
BFX-3000-BWR-11/4 *	250	32	30-35	25	35	60	73	79.5	30.2	58.7	M 12X30*	7/16-11/2
BFX-3000-BWR-11/2 *	210	38	38-43	32	43	65	83	94	35.7	69.8	M 14X35*	1/2-11/2
BFX-3000-BWR-2 *	210	51	48-50	38	50	70	97	102	42.9	77.8	M 14X35*	1/2-11/2
BFX-3000-BWR-21/2 *	160	64	60-63	47	61.8	75	109	114.5	50.8	88.9	M 14X40*	1/2-13/4
BFX-3000-BWR-3	138	76	73-76	58	74	85	131	135	61.9	106.4	M 16X50	5/8-13/4
BFX-3000-BWR-31/2	35	89	88-90	70	90	90	140	152	69.8	120.7	M 16X50	5/8-2
BFX-3000-BWR-4	35	102	95-102	80	102	100	152	162	77.8	130.2	M 16X50	5/8-2
(1)Pressure max. recommended Flanges with 0'Ring and bolts For metric bolts, add "M" after the reference ; for UNC bolts, add "U". Standard delivered with undivided split flanges, specify for split flanges. * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

PORT ASSEMBLY FLANGES BWR REDUCING S.A.E. 6000 / ISO 6162-2
Part N°	PN bar¹	DN	For tube Diameter to…at…	Ø A	Ø H1	L	FF	O	GG	Q	Bolts
Part N°	PN bar¹	DN	For tube Diameter to…at…	Ø A	Ø H1	L	FF	O	GG	Q	Metric	UNC
BFX-6000-BWR-1/2	400	13	16-18	11	17.5	45	48	56.5	18.2	40.5	M 8X30	5/16-11/4
BFX-6000-BWR-3/4	400	19	20-22	13	22	50	60	71	23.8	50.8	M 10X35	3/8-11/2
BFX-6000-BWR-1	400	25	25-28	17.5	28	55	70	81	27.8	57.2	M 12X45	7/16-13/4
BFX-6000-BWR-11/4*	400	32	30-35	22	35	60	78	95	31.8	66.6	M 14X50*	1/2-13/4
BFX-6000-BWR-11/2	400	38	38-43	29	43.8	65	95	113	36.5	79.3	M 16X55	5/8-21/4
BFX-6000-BWR-2	400	51	48-50	35	51	70	114	133	44.5	96.8	M 20X70	3/4-23/4
(1)Pressure max. recommended Flanges with 0'Ring and bolts For metric bolts, add "M" after the reference ; for UNC bolts, add "U". Standard delivered with undivided split flanges, specify for split flanges. * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

PORT ASSEMBLY FLANGES INTEGRALE SOCKET WELD TUBE END - SAE 3000 / SAE 6000

BRIDES DE FIXATION SOCKET WELDING A PASSAGE INTEGRAL

PORT ASSEMBLY FLANGES INTEGRALE SOCKET WELD TUBE END S.A.E. 3000 / ISO 6162-1
Part N°	PN bar¹	DN	Outer diameter tube			Ø L1	Ø L2	ØA	K	L	GG	Q	FF	O	Bolts
			MM	GAZ	SCHD										Metric	UNC
BFX-3000-SWI-1/2"-20.5 BFX-3000-SWI-1/2"-21.7	315	13	20	21.25	21.34	20.5 21.7	30	13	13	60	17.5	38.1	46	54	M 8X25	5/16-1"1/4
BFX-3000-SWI-3/4"-25.5 BFX-3000-SWI-3/4"-27.3		19	25	26.75	26.68	25.5 27.3	35	19	13	68	22.3	47.6	52	65	M 10X30	3/8-1"1/4
BFX-3000-SWI-1"-30.5 BFX-3000-SWI-1"-32.5 BFX-3000-SWI-1"-34 BFX-3000-SWI-1"-35.5		25	30 32 35	33.50	33.40	30.5 32.5 34 35.5	44	25	16	75	26.2	52.4	59	70	M 10X30	3/8-1"1/4
BFX-3000-SWI-1"1/4-38.5* BFX-3000-SWI-1"1/4-40.5* BFX-3000-SWI-1"1/4-43*	200	32	38 40 42	42.25	42.16	38.5 40.5 43	55	32	18	95	30.2	58.7	73	79.5	M 12X30*	716-1"1/2
BFX-3000-SWI-1"1/2-49* BFX-3000-SWI-1"1/2-50.4*		38	50	48.25	48.26	49 50.4	63	38	20	100	35.7	69.8	83	94	M 14X35*	1/2-1"1/2
BFX-3000-SWI-2"-61 * BFX-3000-SWI-2"-65.8 *		51	60 65	60.30	60.32	61 65.8	79	47	22	107	42.9	77.8	97	102	M 14X35*	1/2-1"1/2
BFX-3000-SWI-2"1/2-74* BFX-3000-SWI-2"1/2-77* BFX-3000-SWI-2"1/2-81*	150	64	80	76.10	73.02	74 77 81	98	58	24	130	50.8	88.9	109	114.5	M 14X40*	1/2-1"3/4
BFX-3000-SWI-3"-90.5	100	76	90		88.90	90.5	116	70	28	150	61.9	106.4	131	135	M 16X50	5/8-1"3/4
(1)Pressure max. recommended Flanges with 0'Ring and bolts For metric screws, add "M" after the reference ; for UNC screws, add "U". SWI flanges head may only be fitted with split flanges (the shoulder does not allow a one piece fitting to pass through) * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

PORT ASSEMBLY FLANGES INTEGRALE SOCKET WELD TUBE END S.A.E. 6000 / ISO 6162-2
Part N°	PN bar¹	DN	Outer diameter tube			Ø L1	Ø L2	ØA	K	L	GG	Q	FF	O	Bolts
			MM	GAZ	SCHD										Metric	UNC
BFX-6000-SWI-1/2"-20.5 BFX-6000-SWI-1/2"-21.7 BFX-6000-SWI-1/2"-22.5	380	13	20 22	21.25	21.34	20.5 21.7 22.5	32	13	13	60	18.2	40.5	48	56.5	M 8X30	5/16-1"1/4
BFX-6000-SWI-3/4"-25.7 BFX-6000-SWI-3/4"-27.3 BFX-6000-SWI-3/4"-28.7		19	25 28	26.75	26.68	25.7 27.3 28.7	40	17. 5	13	68	23.8	50.8	60	71	M 10X35	3/8-1"1/2
BFX-6000-SWI-1"-34 BFX-6000-SWI-1"-35.5		25	35	33.5	33.4	34 35.5	48	22	16	75	27.8	57.2	70	81	M 12X45	7/16-1"3/4
(1)Pressure max. recommended Flanges with 0'Ring and bolts For metric screws, add "M" after the reference ; for UNC screws, add "U". SWI flanges head may only be fitted with split flanges (the shoulder does not allow a one piece fitting to pass through) * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

PORT ASSAMBLY FLANGES INTEGRAL SOCKET WELD TUBE END - SAE 3000 / SAE 6000

PORT ASSEMBLY FLANGES REDUCING SOCKET WELD TUBE END - SAE 3000 / SAE 6000

PORT ASSEMBLY FLANGES REDUCING SOCKET WELD TUBE END S.A.E. 3000 / ISO 6162-1
Part N°	PN bar¹	DN	Outer diameter tube			Ø L1	Ø L2	ØA	K	L	GG	Q	FF	O	Bolts
Part N°	PN bar¹	DN	MM	GAZ	SCHD	Ø L1	Ø L2	ØA	K	L	GG	Q	FF	O	Metric	UNC
BFX-3000-SWR-1/2"-16.3 BFX-3000-SWR-1/2"-17.6	315	13	16	16.75	17.14	16.3 17.6	24	12	13	35	17.5	38.1	46	54	M 8X25	5/16-1"1/4
BFX-3000-SWR-3/4"-18.5 BFX-3000-SWR-3/4"-20.5 BFX-3000-SWR-3/4"-21.7		19	18 20	21.25	21.34	18.5 20.5 21.7	31.5	13	13	40	22.3	47.6	52	65	M 10X30	3/8-1"1/4
BFX-3000-SWR-1"-25.5 BFX-3000-SWR-1"-27.3		25	25	26.75	26.68	25.5 27.3	38	19	13	45	26.2	52.4	59	70	M 10X30	3/8-1"1/4
BFX-3000-SWR-1"1/4-30.5 * BFX-3000-SWR-1"1/4-32.5 * BFX-3000-SWR-1"1/4-34 * BFX-3000-SWR-1"1/4-35.5 *	200	32	30 32 35	33.50	33.40	30.5 32.5 34 35.5	43	25	16	50	30.2	58.7	73	79.5	M 12X30*	7/16-1"1/2
BFX-3000-SWR-1"1/2-38.5 * BFX-3000-SWR-1"1/2-40.5 * BFX-3000-SWR-1"1/2-43 *		38	38 40 42	42.25	42.16	38.5 40.5 42.8	50	32	18	55	35.7	69.8	83	94	M 14X35*	1/2-1"1/2
BFX-3000-SWR-2"-49 * BFX-3000-SWR-2"-50.7 *		51	50	48.25	48.26	49 50.7	61.8	38	20	65	42.9	77.8	97	102	M 14X35*	1/2-1"1/2
BFX-3000-SWR-2"1/2-61 * BFX-3000-SWR-2"1/2-65.8 *	150	64	60 65	60.30	60.30	61 65.8	73.8	47	22	75	50.8	88.9	109	114.5	M 14X40*	1/2-1"3/4
BFX-3000-SWR-3"-74 BFX-3000-SWR-3"-77 BFX-3000-SWR-3"-81	100	76	80	76.10	73.02	74 77 81	90	58	25	85	61.9	106.4	131	135	M 16X50	5/8-1"3/4
(1)Pressure max. recommended Flanges with 0'Ring and bolts For metric bolts, add "M" after the reference For UNC bolts, add "U". Standard delivered with undivided split flanges, specify for split flanges. * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

PORT ASSEMBLY FLANGES REDUCING SOCKET WELD TUBE END S.A.E. 6000 / ISO 6162-2
Part N°	PN bar¹	DN	Outer diameter tube			Ø L1	Ø L2	ØA	K	L	GG	Q	FF	O	Bolts
Part N°	PN bar¹	DN	MM	GAZ	SCHD	Ø L1	Ø L2	ØA	K	L	GG	Q	FF	O	Metric	UNC
BFX-6000-SWR-1/2-16.3 BFX-6000-SWR-1/2-17.6	380	13	16	16.75	17.14	16.3 17.6	24	11	13	35	18.2	40.5	48	56.5	M 8X30	5/16-1"1/4
BFX-6000-SWR-3/4-18.5 BFX-6000-SWR-3/4-20.5 BFX-6000-SWR-3/4-21.7		19	18 20	21.25	21.34	18.5 20.5 21.7	32	13	13	40	23.8	50.8	60	71	M 10X35	3/8-1"1/2
BFX-6000-SWR-1"-25.5 BFX-6000-SWR-1"-27.3		25	25	26.75	26.68	25.5 27.3	38	17	13	45	27.8	57.2	70	81	M 12X45	7/16-1"3/4
BFX-6000-SWR-1"1/4-30.5* BFX-6000-SWR-1"1/4-32.5* BFX-6000-SWR-1"1/4-34* BFX-6000-SWR-1"1/4-35.5*	300	32	30 32 35	33.50	33.40	30.5 32.5 34 35.5	44.5	22	16	50	31.8	66.6	78	95	M 14X50*	1/2-1"3/4
BFX-6000-SWR-1"1/2-38.5 BFX-6000-SWR-1"1/2-40.5 BFX-6000-SWR-1"1/2-42.8		38	38 40 42	42.25	42.16	38.5 40.5 42.8	51	29	18	55	36.5	79.3	95	113	M 16X55	5/8-2"1/4
BFX-6000-SWR-2"-49 BFX-6000-SWR-2"-50.8		51	50	48.25	48.26	49 50.8	67	35	20	65	44.5	96.8	114	133	M 20X70	3/4-2"3/4
(1)Pressure max. recommended Flanges with 0'Ring and bolts For metric bolts, add "M" after the reference For UNC bolts, add "U". Standard delivered with undivided split flanges, specify for split flanges.

BRIDES DE FIXATION A EMBOUTS FILEPORT ASSEMBLY FLANGES WITH MALE BSP Co or NPT THREAD - SAE 3000 / SAE 6000

BRIDES DE FIXATION A EMBOUTS FILETES GAZ CO ou NPT

PORT ASSEMBLY FLANGES WITH MALE BSP Co or NPT THREAD S.A.E. 3000 / ISO 6162-1
Part N°	PN Bar¹	DN	F Gaz co.	Ø A	L	GG	Q	FF	O	P	Bolts
											Metric	UNC
BFX-3000-F-G-CO-1/2"-A BFX-3000-F-G-CO-1/2"-B	300	13	1/2" 3/8"	12 10	50	17.5	38.1	46	54	19	M 8X25	5/16"-1"1/4
BFX-3000-F-G-CO-3/4"-A BFX-3000-F-G-CO-3/4"-B		19	3/4" 1/2"	17 12	55	22.3	47.6	52	65	27	M10X30	3/8"-1"1/4
BFX-3000-F-G-CO-1"-A BFX-3000-F-G-CO-1"-B		25	1" 3/4"	22 17	60	26.2	52.4	59	70	32	M10X30	3/8"-1"1/4
BFX-3000-F-G-CO-1"1/4-A * BFX-3000-F-G-CO-1"1/4-B *	150	32	1"1/4 1"	27 22	65	30.2	58.7	73	79.5	41	M12X30 *	7/16"-1"1/2
BFX-3000-F-G-CO-1"1/2-A * BFX-3000-F-G-CO-1"1/2-B *		38	1"1/2 1"1/4	32 27	70	35.7	69.8	83	94	46	M14X35 *	1/2"-1"1/2
BFX-3000-F-G-CO-2"-A * BFX-3000-F-G-CO-2"-B *		51	2" 1"1/2	40 30	75	42.9	77.8	97	102	55	M14X35 *	1/2"-1"1/2
(1)Pressure max. recommended Flanges with 0'Ring and bolts For metric bolts, add "M" after the reference ; for UNC bolts, add "U". For threaded BSPP or NPT, replace G CO by G CYL or NPT into the reference * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

PORT ASSEMBLY FLANGES WITH MALE BSP Co or NPT THREAD S.A.E. 6000 / ISO 6162-2
Part N°	PN Bar¹	DN	F Gaz co.	Ø A	L	GG	Q	FF	O	P	Bolts
											Metric	UNC
BFX-6000-F-G-CO-1/2"-A BFX-6000-F-G-CO-1/2"-B	350	13	1/2" 3/8"	12 10	50 50	18.2	40.5	48	56	19	M 8X30	5/16"-1"1/4
BFX-6000-F-G-CO-3/4"-A BFX-6000-F-G-CO-3/4"-B		19	3/4" 1/2"	17 12	60 60	23.8	50.8	60	71	26	M10X35	3/8"-1"1/2
BFX-6000-F-G-CO-1"-A BFX-6000-F-G-CO-1"-B		25	1" 3/4"	22 17	70 70	27.7	57.1	70	81	32	M12X45	7/16"-1"3/4
BFX-6000-F-G-CO-1"1/4-A * BFX-6000-F-G-CO-1"1/4-B *	250	32	1"1/4 1"	27 22	75 75	31.7	66.7	78	95	36	M14X50*	1/2"-1"3/4
BFX-6000-F-G-CO-1"1/2-A BFX-6000-F-G-CO-1"1/2-B		38	1"1/2 1"1/4	32 27	80 80	36.5	79.4	95	113	41	M16X55	5/8"-2"1/4
BFX-6000-F-G-CO-2"-A BFX-6000-F-G-CO-2"-B	200	51	2" 1"1/2	40 30	90 90	44.4	96.8	114	133	55	M20X70	3/4"-2"3/4
(1)Pressure max. recommended Flanges with 0'Ring and bolts For metric bolts, add "M" after the reference ; for UNC bolts, add "U". For threaded BSPP or NPT, replace G CO by G CYL or NPT into the reference * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

PORT ASSEMBLY FLANGES WITH MALE UNF-JIC 74° THREAD - SAE 3000 / SAE 6000

BRIDES DE FIXATION FILETEES UNF MALE JIC

PORT ASSEMBLY FLANGES WITH MALE UNF-JIC 74° THREAD S.A.E.3000 / ISO 6162-1
Part N°	PN Bar¹	DN	Ø F UNF-2A	Q	GG	FF2	O²	L	U	Bolts
Part N°	PN Bar¹	DN	Ø F UNF-2A	Q	GG	FF2	O²	L	U	Metric	UNC
BFX-3000-F-JIC-1/2"-A BFX-3000-F-JIC-1/2"-B BFX-3000-F-JIC-1/2"-C	250	13	3/4"-16 7/8"-14 1"1/16-12	38.1	17.5	47	57	41 41 46	16	M 8X30	5/16"-1"1/4
BFX-3000-F-JIC-3/4"-A BFX-3000-F-JIC-3/4"-B BFX-3000-F-JIC-3/4"-C		19	7/8"-14 1"1/16-12 1"5/16-12	47.6	22.3	49	66	47 49 50	18	M 10X35	3/8"-1"1/2
BFX-3000-F-JIC-1"-A BFX-3000-F-JIC-1"-B BFX-3000-F-JIC-1"-C		25 25	1"1/16-12 1"5/16-12 1"5/8-12	52.4	26.2	53	71	51 52 54	18	M 10X35	3/8"-1"1/2
BFX-3000-F-JIC-1"1/4-A * BFX-3000-F-JIC-1"1/4-B * BFX-3000-F-JIC-1"1/4-C *		32	1"5/16-12 1"5/8-12 1"7/8-12	58.7	30.2	69	80	56 58 61	21	M 10X40 * ou M 12X40	7/16"-1"1/2
BFX-3000-F-JIC-1"1/2-A * BFX-3000-F-JIC-1"1/2-B *	210	38	1"5/8-12 1"7/8-12	69.8	35.7	77	94	64 67	24	M 12X45 *ou M 14X45	1/2"-1"3/4
(1)Pressure max. recommended Flanges with 0'Ring and bolts For metric bolts, add "M" after the reference ; for UNC bolts, add "U". One piece flanges threaded from the block : on request made with threaded flanges head with JIC male and separate flange. * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

PORT ASSEMBLY FLANGES WITH MALE UNF-JIC 74° THREAD S.A.E. 6000 / ISO 6262-2
Part N°	PN Bar¹	DN	Ø F UNF-2A	Q	GG	FF2	O²	L	U	Bolts
										Metric	UNC
BFX-6000-F-JIC-1/2"-A BFX-6000-F-JIC-1/2"-B BFX-6000-F-JIC-1/2"-C	350	13	3/4"-16 7/8"-14 1"1/16-12	40.5	18.3	47	57	42 45 47	16	M 8X30	5/16"-1"1/4
BFX-6000-F-JIC-3/4"-A BFX-6000-F-JIC-3/4"-B BFX-6000-F-JIC-3/4"-C		19	7/8"-14 1"1/16-12 1"5/16-12	50.8	23.8	53	71	49 51 52	18	M 10X35	3/8"-1"1/2
BFX-6000-F-JIC-1"-A BFX-6000-F-JIC-1"-B BFX-6000-F-JIC-1"-C		25	1"1/16-12 1"5/16-12 1"5/8-12	57.1	27.8	69	80	58 59 61	21	M 12X40	7/16"-1"3/4
	250
BFX-6000-F-JIC-1"1/4-A * BFX-6000-F-JIC-1"1/4-B * BFX-6000-F-JIC-1"1/4-C *		32	1"5/16-12 1"5/8-12 1"7/8-12	66.7	31.6	77	94	64 66 69	24	M 14X45 *	1/2"-1"3/4
BFX-6000-F-JIC-1"1/2-A BFX-6000-F-JIC-1"1/2-B		38	1"5/8-12 1"7/8-12	79.4	36.7	89	106	70 73	27	M 16X55	5/8"-2"1/4
(1)Pressure max. recommended Flanges with 0'Ring and bolts For metric bolts, add "M" after the reference ; for UNC bolts, add "U". One piece flanges threaded from the block : on request made with threaded flanges head with JIC male and separate flange. * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

PORT ASSEMBLY FLANGES FEMALE BSPP or NPT THREAD - SAE 3000 / SAE 6000

BRIDES DE FIXATION TARAUDEES BSPP OU NPT

PORT ASSEMBLY FLANGES FEMALE BSPP or NPT THREAD S.A.E. 3000 / ISO 6162-1
Part N°	PN Bar¹	DN	Ø F	L	GG	Q	FF	ØA	K	U	O	Bolts
			BSPP									Metric	UNC
BFX-3000-T-BSP-1/2" BFX-3000-T-BSP-1/2"-TAR-3/8"	345	13	1/2" 3/8"	36	17.5	38.1	47	13	15 13	16	57	M 8X30	5/16'-1"1/4
BFX-3000-T-BSP-3/4"		19	3/4"	36	22.3	47.6	49	19	18	18	66	M 10X35	3/8"-1"1/2
BFX-3000-T-BSP-3/4"-TAR-1/2"			1/2"					13
BFX-3000-T-BSP-1" BFX-3000-T-BSP-1"-TAR-3/4"		25	1" 3/4"	38	26.2	52.4	53	25 19	20	18	71	M 10X35	3/8"-1"1/2
BFX-3000-T-BSP-1"1/4 *	278	32	1"1/4	41	30.2	58.7	69	31	22	21	80	M 10X40 ou	7/16"-1"1/2
BFX-3000-T-BSP-1"1/4-TAR-1" *			1"					25				M 12X40*
BFX-3000-T-BSP-1"1/2 * BFX-3000-T-BSP-1"1/2-TAR-1"1/4 *	210	38	1"1/2 1"1/4	44	35.7	69.9	77	38 31	24	25	94	M 12X45 ou M 14X45*	1/2"-1"3/4
BFX-3000-T-BSP-2" *		51	2"	45	42.9	77.8	89	50	26	25	103	M 12X45 ou	1/2"-1"3/4
BFX-3000-T-BSP-2"-TAR-1"1/2 *			1"1/2					38				M 14X45*
BFX-3000-T-BSP-2"1/2 * BFX-3000-T-BSP-2"1/2-TAR-2" *	175	64	2"1/2 2"	50	50.8	88.9	101	63 50	30	25	115	M 12X45 ou M 14 X 45*	1/2-1"3/4
BFX-3000-T-BSP-3"	138	76	3"	50	61.9	106.4	124	73	30	27	135	M 16X50	5/8"-2"
BFX-3000-T-BSP-3"-TAR-2"1/2			2"1/2					63
BFX-3000-T-BSP-3"1/2	35	89	3"1/2	50	69.8	120.7	136	89	30	27	152	M 16X50	5/8"-2"
BFX-3000-T-BSP-4"	35	102	4"	50	77.8	130.2	146	99	30	27	162	M 16X50	5/8"-2"
(1)Pressure max. recommended Flanges with 0'Ring and bolts For metric bolts, add "M" after the reference ; for UNC bolts, add "U". For tapped NPT, replace BSP by NPT into the reference * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

PORT ASSEMBLY FLANGES FEMALE BSPP or NPT THREAD S.A.E. 6000 / ISO 6162-2
Part N°	PN Bar¹	DN	Ø F	L	GG	Q	FF	ØA	K	U	O	Bolts
			BSP									Metric	UNC
BFX-6000-T-BSP-1/2" BFX-6000-T-BSP-1/2"-TAR-3/8"	400	13	1/2" 3/8	36	18.2	40.5	47	14	15 13	16	57	M 8X30	5/16"-1"1/4
BFX-6000-T-BSP-3/4"		19	3/4"	36	23.8	50.8	53	19	18	19	71	M 10X35	3/8"-1"1/2
BFX-6000-T-BSP-3/4"-TAR-1/2"			1/2"					14
BFX-6000-T-BSP-1" BFX-6000-T-BSP-1"-TAR-3/4"		25	1" 3/4"	44	27.8	57.2	69	25 19	20	24	80	M 12X45	7/16"-1"3/4
BFX-6000-T-BSP-1"1/4 *		32	1"1/4	44	31.6	66.6	77	31	22	27	94	M 14X50*	1/2"-1"3/4
BFX-6000-T-BSP-1"1/4-TAR-1" *			1"					25
BFX-6000-T-BSP-1"1/2 BFX-6000-T-BSP-1"1/2-TAR-1"1/4		38	1"1/2 1"1/4	51	36.5	79.3	89	38 31	24	30	106	M 16X55	5/8"-2"1/4
BFX-6000-T-BSP-2"		51	2"	58	44.5	96.8	116	50	33	37	135	M 20X70	3/4"-2"1/2
(1)Pressure max. recommended Flanges with 0'Ring and bolts For metric bolts, add "M" after the reference ; for UNC bolts, add "U". For tapped NPT, replace BSP by NPT into the reference * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

PORT ASSEMBLY FLANGES FEMALE UN/UNF THREAD FOR O-RING - SAE 3000 / SAE 6000

BRIDES DE FIXATION TARAUDEES DIN METRIQUES CYLINDRIQUES ETANCHEITE PAR JOINT ORING

PORT ASSEMBLY FLANGES FEMALE UN/UNF THREAD for O-ring S.A.E. 3000 / ISO 6162-1
Part N°	PN Bar¹	DN	Ø F UN / UNF	L	GG	Q	FF	ØA	K	U	O	Bolts
Part N°	PN Bar¹	DN	Ø F UN / UNF	L	GG	Q	FF	ØA	K	U	O	Metric	UNC
BFX-3000-T-UNF-1/2"--A	345	13	3/4-16	36	17.5	38.1	47	13	17	16	57	M 8X30	5/16'-1"1/4
BFX-3000-T-UNF-3/4"-A		19	7/8"-14	36	22.3	47.6	49	19	17	18	66	M 10X35	3/8"-1"1/2
BFX-3000-T-UNF-3/4"-B			1"1/16-12						23
BFX-3000-T-UNF-1"-A BFX-3000-T-UNF-1"-B		25	1"1/16-12 1"5/16-12	38	26.2	52.4	53	25	23	18	71	M 10X35	3/8"-1"1/2
BFX-3000-T-UNF-1"1/4-A*	278	32	1"5/16-12	41	30.2	58.7	69	31	23	21	80	M 10X40 ou	7/16"-1"1/2
BFX-3000-T-UNF-1"1/4-B*	278		1"5/8-12									M 12X40*
BFX-3000-T-UNF-1"1/2-A* BFX-3000-T-UNF-1"1/2-B*	210	38	1"5/8-12 1"7/8-12	44	35.7	69.8	77	38	23	25	94	M 12X45 ou M 14X45*	1/2"-1"3/4
(1)Pressure max. recommended For metric bolts, add "M" after the reference ; for UNC bolts, add "U". * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

PORT ASSEMBLY FLANGES FEMALE UN/UNF THREAD for O-ring S.A.E. 6000 / ISO 6162-2
Part N°	PN Bar¹	DN	Ø F UN / UNF	L	GG	Q	FF	ØA	K	U	O	Bolts
Part N°	PN Bar¹	DN	Ø F UN / UNF	L	GG	Q	FF	ØA	K	U	O	Metric	UNC
BFX-6000-T-UNF-1/2-A	400	13	3/4"-16	36	18.3	40.5	47	13	17	16	57	M 8X30	5/16"-1"1/4
BFX-6000-T-UNF-3/4-A		19	7/8"-14	36	23.8	50.8	53	19	17	19	71	M 10X35	3/8"-1"1/2
BFX-6000-T-UNF-3/4-B			1"1/16-12						23
BFX-6000-T-UNF-1"-A BFX-6000-T-UNF-1"-B		25	1"1/16-12 1"5/16-12	44	27.8	57.1	69	25	23	24	80	M 12X45	7/16"-1"3/4
BFX-6000-T-UNF-1"1/4-A*		32	1"5/16-12	44	31.6	66.7	77	31	23	27	94	M 14X50 *	1/2"-1"3/4
BFX-6000-T-UNF-1"1/4-B*			1"5/8-12
BFX-6000-T-UNF-1"1/2-A BFX-6000-T-UNF-1"1/2-B		38	1"5/8-12 1"7/8-12	51	36.7	79.4	89	38	23	30	106	M 16X55	5/8"-2"1/4
(1)Pressure max. recommended For metric bolts, add "M" after the reference ; for UNC bolts, add "U". * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

PORT ASSEMBLY FLANGES FEMALE METRIC THREAD for O-ring (ISO 6149-1) - SAE 3000 / SAE 6000

PORT ASSEMBLY FLANGES FEMALE METRIC THREAD for O-ring ( ISO 6149-1 ) S.A.E. 3000 / ISO 6162-1
Part N°	PN Bar¹	DN	Ø F	L	GG	Q	FF	ØA	K	U	O	Bolts
			DIN									Metric	UNC
BFX-3000-T-DIN-1/2"-A BFX-3000-T-DIN-1/2"-B	345	13	18X1.5 20X1.5	36	17.5	38.1	47	13	15	16	57	M 8X30	5/16'-1"1/4
BFX-3000-T-DIN-3/4"-A		19	22X1.5	36	22.3	47.6	49	19	16	18	66	M 10X35	3/8"-1"1/2
BFX-3000-T-DIN-3/4"-B			27X2						19
BFX-3000-T-DIN-1"-A BFX-3000-T-DIN-1"-B		25	27X2 33X2	38	26.2	52.4	53	25	19	18	71	M 10X35	3/8"-1"1/2
BFX-3000-T-DIN-1"1/4-A*	278	32	33X2	41	30.2	58.7	69	31	19	21	80	M 10X40 ou	7/16"-1"1/2
BFX-3000-T-DIN-1"1/4-B*			42X2						20			M 12X40*
BFX-3000-T-DIN-1"1/2-A* BFX-3000-T-DIN-1"1/2-B*	210	38	42X2 48X2	44	35.7	69.8	77	38	20 22	25	94	M 12X45 ou M 14X45*	1/2"-1"3/4
(1)Pressure max. recommended Flanges with 0'Ring and bolts For metric bolts, add "M" after the reference ; for UNC bolts, add "U". * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

PORT ASSEMBLY FLANGES FEMALE METRIC THREAD for O-ring ( ISO 6149-1 ) S.A.E. 6000 / ISO 6162-2
Part N°	PN Bar¹	DN	Ø F	L	GG	Q	FF	ØA	K	U	O	Bolts
			DIN									Metric	UNC
BFX-6000-T-DIN-1/2-A BFX-6000-T-DIN-1/2-B	400	13	18X1.5 20X1.5	36	18.2	40.5	47	13	15	16	57	M 8X30	5/16"-1"1/4
BFX-6000-T-DIN-3/4-A		19	22X1.5	36	23.8	50.8	53	19	16	19	71	M 10X35	3/8"-1"1/2
BFX-6000-T-DIN-3/4-B			27X2						19
BFX-6000-T-DIN-1"-A BFX-6000-T-DIN-1"-B		25	27X2 33X2	44	27.8	57.2	69	25	19	24	80	M 12X45	7/16"-1"3/4
BFX-6000-T-DIN-1"1/4-A*		32	33X2	44	31.6	66.6	77	31	19	27	94	M 14X50 *	1/2"-1"3/4
BFX-6000-T-DIN-1"1/4-B*			42X2						20
BFX-6000-T-DIN-1"1/2-A BFX-6000-T-DIN-1"1/2-B		38	42X2 48X2	51	36.5	79.3	89	38	20 22	30	106	M 16X55	5/8"-2"1/4
(1)Pressure max. recommended Flanges with 0'Ring and bolts For metric bolts, add "M" after the reference ; for UNC bolts, add "U". * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

UNION ASSEMBLY FLANGES BUTT WELD TUBE END (MONOBLOC) - SAE 3000 / SAE 6000

UNION ASSEMBLY FLANGES BUTT WELD TUBE END (MONOBLOC) S.A.E. 3000 / ISO 6162-1
Part N°	PN bar¹	DN	ØA	ØB	L	GG	Q	FF	O	U	Bolts
Part N°	PN bar¹	DN	ØA	ØB	L	GG	Q	FF	O	U	Metric	UNC
BFX-MONO-3000-BWI-1/2"	345	13	21.6	13	36	17.5	38.1	47	57	16	M 8X30	5/16"-1"1/4
BFX-MONO-3000-BWI-3/4"	345	19	27.2	19	36	22.3	47.6	49	66	18	M 10X35	3/8"-1"1/2
BFX-MONO-3000-BWI-1"	315	25	34.5	25	38	26.2	52.4	53	71	18	M 10X35	3/8"-1"1/2
BFX-MONO-3000-BWI-1"1/4	250	32	42.8	31	41	30.2	58.7	69	80	21	M 10X40 ou M 12X40*	7/16"-1"1/2
BFX-MONO-3000-BWI-1"1/2	210	38	48.6	38	44	35.7	69.8	77	94	25	M 12X45 ou M 14X45*	1/2"-1"3/4
BFX-MONO-3000-BWI-2"	210	51	61	50	45	42.9	77.8	89	103	25	M 12X45 ou M 14X45*	1/2"-1"3/4
BFX-MONO-3000-BWI-2"1/2	160	64	76.6	63	50	50.8	88.9	101	115	25	M 12X45 ou M 14X45*	1/2"-1"3/4
BFX-MONO-3000-BWI-3"	138	76	89	73	50	61.9	106.4	124	135	27	M 16X50	5/8"-2"
BFX-MONO-3000-BWI-3"1/2	35	89	103	89	50	69.8	120.7	137	153	27	M 16X50	5/8"-2"
BFX-MONO-3000-BWI-4"		102	115	99	50	77.8	130.2	147	163	27	M 16X50	5/8"-2"
BFX-MONO-3000-BWI-5"		127	141	120	50	92	152.4	180	184	28	M 16X55	5/8"-2"1/4
(1)Pressure max. recommended Flanges with 0'Ring and bolts For metric bolts, add "M" after the reference ; for UNC bolts, add "U". * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

UNION ASSEMBLY FLANGES BUTT WELD TUBE END (MONOBLOC) S.A.E. 6000 / ISO 6162-2
Part N°	PN bar¹	DN	ØA	ØB	L	GG	Q	FF	O	U	Bolts
Part N°	PN bar¹	DN	ØA	ØB	L	GG	Q	FF	O	U	Metric	UNC
BFX-MONO-6000-BWR-1/2"	400	13	17.5	10	36	18.2	40.5	47	57	18	M 8X30	5/16"-1"1/4
BFX-MONO-6000-BWI-1/2"		13	21.6	13	36	18.2	40.5	47	57	18	M 8X30	5/16"-1"1/4
BFX-MONO-6000-BWI-3/4"		19	27.2	18	36	23.8	50.8	53	71	18	M 10X35	3/8"-1"1/2
BFX-MONO-6000-BWI-1"		25	34.5	22	44	27.8	57.2	66	80	24	M 12X45	7/16"-1"3/4
BFX-MONO-6000-BWI-1"1/4 *		32	42.8	28	44	31.8	66.6	77	94	25	M 14X50 *	1/2"-1"3/4
BFX-MONO-6000-BWI-1"1/2		38	48.6	32	51	36.5	79.3	89	106	29	M 16X55	5/8"-2"1/4
BFX-MONO-6000-BWI-2"		51	61	41	70	44.5	96.8	116	135	35	M 20X70	3/4"-2"1/2
BFX-MONO-6000-BWI-2"1/2		64	73.6	50	75	58.7	123.8	150	166	45	M 24X90	-
BFX-MONO-6000-BWI-3"		76	90	58	90	71.4	152.4	178	208	55	M 30X110	-
(1)Pressure max. recommended Flanges with 0'Ring and bolts For metric bolts, add "M" after the reference ; for UNC bolts, add "U". * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

90° PORT ASSEMBLY FLANGES BUTT WELDING - SAE 3000 / SAE 6000

90° PORT ASSEMBLY FLANGES SOCKET WELDING - SAE 3000 / SAE 6000

90° PORT ASSEMBLY FLANGES FEMALE THREADED BSP - SAE 3000 / SAE 6000

BRIDES DE FIXATION TARAUDEES GAZ OU NPT COUDEES 90

90° PORT ASSEMBLY FLANGES FEMALE THREADED BSP S.A.E. 3000 / ISO 6162-1
Part N°	PN Bar¹	DN	ØF	ØA	M	N	L	Ø H	K	O	Q	FF	GG	Bolts
Part N°	PN Bar¹	DN	ØF	ØA	M	N	L	Ø H	K	O	Q	FF	GG	Metric	UNC
BFX-90°-3000-T-BSP-1/2"	345	13	1/2"	13	17	18	13	34	19	57	38.1	59	17.5	M 8	5/16"
BFX-90°-3000-T-BSP-3/4"		19	3/4"	19	18	22	15	38.5	19	68	47.6	63	22.3	M 10	3/8"
BFX-90°-3000-T-BSP-1"		25	1"	25	19	28	15	44.5	19	74	52.4	68	26.2	M 10	3/8"
BFX-90°-3000-T-BSP-1"1/4*	278	32	1"1/4	31	22	30	17	53.5	22	81	58.7	84	30.2	M 10 ou M 12*	7/16"
BFX-90°-3000-T-BSP-1"1/2*	210	38	1"1/2	38	25	36	18	62.5	24	95	69.8	97	35.7	M 12 ou M 14*	1/2"
BFX-90°-3000-T-BSP-2"*	210	51	2"	50	25	41	18	77	26	105	77.8	109	42.9	M 12 ou M 14*	1/2"
(1)Pressure max. recommended Flanges with 0'Ring and bolts For threaded NPT, replace G CO by NPT into the reference Protection : Yellow galvanized For metric bolts, add "M" after the reference ; for UNC bolts, add "U". * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

90° PORT ASSEMBLY FLANGES FEMALE THREADED BSP S.A.E. 6000 / ISO 6162-2
Part N°	PN Bar¹	DN	ØF	ØA	M	N	L	Ø H	K	O	Q	FF	GG	Bolts
Part N°	PN Bar¹	DN	ØF	ØA	M	N	L	Ø H	K	O	Q	FF	GG	Metric	UNC
BFX-90°-6000-T-BSP-1/2"	400	13	1/2"	13	17	18	13	34	19	57	40.5	59	18.2	M 8	5/16"
BFX-90°-6000-T-BSP-3/4"		19	3/4"	19	20	28	15	44.5	19	68	50.8	68	23.8	M 10	3/8"
BFX-90°-6000-T-BSP-1"		25	1"	25	24	30	19	53.5	19	74	57.2	84	27.8	M 12	7/16"
BFX-90°-6000-T-BSP-1"1/4*		32	1"1/4	31	25	36	21	62.5	22	81	66.6	97	31.8	M 14 *	1/2"
BFX-90°-6000-T-BSP-1"1/2		38	1"1/2	38	26	41	25	77	24	95	79.3	109	36.5	M 16	5/8"
BFX-90°-6000-T-BSP-2"		51	2"	50	35	45	32	87	26	105	96.8	133	44.4	M 20	3/4"
(1)Pressure max. recommended Flanges with 0'Ring and bolts For threaded NPT, replace G CO by NPT into the reference Protection : Yellow galvanized For metric bolts, add "M" after the reference ; for UNC bolts, add "U". * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

90° PORT ASSEMBLY FLANGES MALE 24° CONE END DIN 2353 (ISO 8434-1)
SAE 3000 / SAE 6000

BRIDES DE FIXATION 90 FILETEES METRIQUES A CONE INTERIEUR 24 NORME DIN 2353

90° PORT ASSEMBLY FLANGES MALE 24° CONE END DIN 2353 ( ISO 8434-1 ) S.A.E. 3000 / ISO 6162-1
Part N°	PN bar¹	DN	Ø F	Ø D	Ø A	Q	GG	G	H	I	L	Bolts
												Metric	UNC
BFX-90°-3000-F-DIN-1/2"-A BFX-90°-3000-F-DIN-1/2"-B BFX-90°-3000-F-DIN-1/2"-C	315	13	20X1.5 22X1.5 24X1.5	12 S 15 L 16 S	8 11 12	38.1	17.5	36	16	18	14	M 8	5/16"
	350
BFX-90°-3000-F-DIN-3/4"-A			24X1.5	16 S	12
BFX-90°-3000-F-DIN-3/4"-B		19	30X2.0	20 S	16	47.6	22.3	38	18	22	14	M 10	3/8"
BFX-90°-3000-F-DIN-3/4"-C	160		30X2.0	22 L	18
BFX-90°-3000-F-DIN-1"-A BFX-90°-3000-F-DIN-1"-B BFX-90°-3000-F-DIN-1"-C	315	25	30X2.0 36X2.0 36X2.0	20 S 25 S 28 L	16 20 23	52.4	26.2	42	19	28	14	M 10	3/8"
	160
BFX-90°-3000-F-DIN1"1/4-A*	250		36X2.0	25 S	20							M10
BFX-90°-3000-F-DIN-1"1/4-B*		32	42X2.0	30 S	25	58.7	30.2	50	22	30	18	ou	7/16"
BFX-90°-3000-F-DIN-1"1/4-C*	160		45X2.0	35 L	30							M 12*
BFX-90°-3000-F-DIN-1"1/2-A* BFX-90°-3000-F-DIN-1"1/2-B* BFX-90°-3000-F-DIN-1"1/2-C*		38	45X2.0 52X2.0 52X2.0	35 L 38 S 42 L	30 32 36	69.8	35.7	58	25	36	18	M 12 ou M 14*	1/2"
	200
	160
(1)Pressure max. recommended Flanges with 0'Ring and bolts Protection : Yellow galvanized For metric bolts, add "M" after the reference ; for UNC bolts, . add "U". * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

90° PORT ASSEMBLY FLANGES MALE 24° CONE END DIN 2353 ( ISO 8434-1 ) S.A.E. 6000 / ISO 6162-2
Part N°	PN bar¹	DN	Ø F	Ø D	Ø A	Q	GG	G	H	I	L	Bolts
												Metric	UNC
BFX-90°-6000-F-DIN-1/2"-A BFX-90°-6000-F-DIN-1/2"-B BFX-90°-6000-F-DIN-1/2"-C	400	13	20X1.5 22X1.5 24X1.5	12 S 14 S 16 S	8 10 12	40.5	18.2	36	16	20	14	M 8	5/16"
BFX-90°-6000-F-DIN-3/4"-A			24X1.5	16 S	12
BFX-90°-6000-F-DIN-3/4"-B		19	30X2.0	20 S	20	50.8	23.8	41	19	26	14	M 10	3/8"
BFX-90°-6000-F-DIN-3/4"-C	160		30X2.0	22 L	23
BFX-90°-6000-F-DIN-1"-A BFX-90°-6000-F-DIN-1"-B BFX-90°-6000-F-DIN-1"-C	400	25	30X2.0 36X2.0 36X2.0	20 S 25 S 28 L	16 20 23	57.2	27.8	50	24	30	14	M 12	7/16"
	160
BFX-90°-6000-F-DIN-1"1/4-A*	400		36X2.0	25 S	20
BFX-90°-6000-F-DIN-1"1/4-B*		32	42X2.0	30 S	25	66.6	31.8	58	25	36	18	M 14 *	1/2"
BFX-90°-6000-F-DIN-1"1/4-C*	160		45X2.0	35 L	30
BFX-90°-6000-F-DIN-1"1/2-A BFX-90°-6000-F-DIN-1"1/2-B BFX-90°-6000-F-DIN-1"1/2-C	400	38	42X2.0 52X2.0 52X2.0	30 S 38 S 42 L	25 32 36	79.3	36.5	65	26	41	18	M 16	5/8"
	160
(1)Pressure max. recommended Flanges with 0'Ring and bolts Protection : Yellow galvanized For metric bolts, add "M" after the reference ; for UNC bolts, . add "U". * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

90° PORT ASSEMBLY FLANGES MALE BSPP CONE END (60°)
SAE 3000 / SAE 6000

BRIDES DE FIXATION FILETEES MALE BSP COUDEES 90

90° PORT ASSEMBLY FLANGES MALE BSPP CONE END ( 60°) S.A.E. 3000 / ISO 6162-1
Part N°	PN Bar¹	DN	Ø F BSPP	Q	GG	D	E	M	L	Bolts
Part N°	PN Bar¹	DN	Ø F BSPP	Q	GG	D	E	M	L	Metric	UNC
BFX-90°-3000-F-MBSP-1/2"-A BFX-90°-3000-F-MBSP-1/2"-B BFX-90°-3000-F-MBSP-1/2"-C	345	13	3/8" 1/2" 3/4"	38.1	17.5	17 17 20	37 39 40	16	14	M 8	5/16"
BFX-90°-3000-F-MBSP-3/4"-A			1/2"			20	41
BFX-90°-3000-F-MBSP-3/4"-B		19	3/4"	47.6	22.3	20	44	18	14	M 10	3/8"
BFX-90°-3000-F-MBSP-3/4"-C			1"			25	45
BFX-90°-3000-F-MBSP-1"-A BFX-90°-3000-F-MBSP-1"-B BFX-90°-3000-F-MBSP-1"-C		25	3/4" 1" 1"1/4	52.4	26.2	20 25 31	47 48 49	19	14	M 10	3/8"
BFX-90°-3000-F-MBSP-1"1/4-A*	278		1"			25	54			M 10
BFX-90°-3000-F-MBSP-1"1/4-B*		32	1"1/4	58.7	30.2	31	55	22	18	ou	7/16"
BFX-90°-3000-F-MBSP-1"1/4-C*			1"1/2			37	56			M 12*
BFX-90°-3000-F-MBSP-1"1/2-A* BFX-90°-3000-F-MBSP-1"1/2-B*	210	38	1"1/4 1"1/2	69.8	35.7	31 37	59 61	25	18	M 12 ou M 14*	1/2"
(1)Pressure max. recommended Flanges with 0'Ring and bolts Protection : Yellow galvanized Sealing on 60° cone in front of threading For metric bolts, add "M" after the reference ; for UNC bolts, add "U". * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

90° PORT ASSEMBLY FLANGES MALE BSPP CONE END ( 60°) S.A.E. 6000 / ISO 6162-2
Part N°	PN bar¹	DN	Ø F BSPP	Q	GG	D	E	M	L	Bolts
Part N°	PN bar¹	DN	Ø F BSPP	Q	GG	D	E	M	L	Metric	UNC
BFX-90°-6000-F-MBSP-1/2"-A BFX-90°-6000-F-MBSP-1/2"-B BFX-90°-6000-F-MBSP-1/2"-C	400	13	3/8" 1/2" 3/4"	40.5	18.2	17 17 20	37 39 40	16	14	M 8	5/16"
BFX-90°-6000-F-MBSP-3/4"-A			1/2"			20	45
BFX-90°-6000-F-MBSP-3/4"-B		19	3/4"	50.8	23.8	20	48	19	14	M 10	3/8"
BFX-90°-6000-F-MBSP-3/4"-C			1"			25	50
BFX-90°-6000-F-MBSP-1"-A BFX-90°-6000-F-MBSP-1"-B BFX-90°-6000-F-MBSP-1"-C		25	3/4" 1" 1"1/4	57.2	27.8	25 25 31	52 54 55	24	18	M 12	7/16"
BFX-90°-6000-F-MBSP-1"1/4-A*			1"			31	59
BFX-90°-6000-F-MBSP-1"1/4-B*		32	1"1/4	66.6	31.8	31	59	25	18	M 14*	1/2"
BFX-90°-6000-F-MBSP-1"1/4-C*			1"1/2			37	61
BFX-90°-6000-F-MBSP-1"1/2-A BFX-90°-6000-F-MBSP-1"1/2-B		38	1"1/4 1"1/2	79.3	36.5	37 37	64 66	26	20	M 16	5/8"
(1)Pressure max. recommended Flanges with 0'Ring and bolts Protection : Yellow galvanized Sealing on 60° cone in front of threading For metric bolts, add "M" after the reference ; for UNC bolts, add "U". * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

90° PORT ASSEMBLY FLANGES MALE UNF THREAD (JIC 74°)
SAE 3000 / SAE 6000

BRIDES DE FIXATION FILETEES MALE JIC COUDEES 90

90° PORT ASSEMBLY FLANGES MALE UNF THREAD (JIC 74°) S.A.E. 3000 / ISO 6162-1
Part N°	PN bar¹	DN	Ø F	Q	GG	D	E	H	L	Bolts
Part N°	PN bar¹	DN	Ø F	Q	GG	D	E	H	L	Metric	UNC
BFX-90°-3000-F-JIC-1/2"-A BFX-90°-3000-F-JIC-1/2"-B BFX-90°-3000-F-JIC-1/2"-C	250	13	3/4"-16 7/8"-14 1"1/16-12	38,1	17.5	17 17 20	40 42 43	16	14	M 8	5/16"
BFX-90°-3000-F-JIC-3/4"-A BFX-90°-3000-F-JIC-3/4"-B BFX-90°-3000-F-JIC-3/4"-C		19	7/8"-14 1"1/16-12 1"5/16-12	47.6	22.3	20 20 25	45 47 48	18	14	M 10	3/8"
BFX-90°-3000-F-JIC-1"-A BFX-90°-3000-F-JIC-1"-B		25	1"1/16-12 1"5/16-12	52.4	26.2	20 25	50 51	19	15	M 10	3/8"
BFX-90°-3000-F-JIC-1"1/4-A* BFX-90°-3000-F-JIC-1"1/4-B* BFX-90°-3000-F-JIC-1"1/4-C*		32	1"5/16-12 1"5/8-12 1"7/8-12	58.7	30.2	25 31 37	56 58 61	22	18	M 10 ou M 12*	7/16"
BFX-90°-3000-F-JIC-1"1/2-A* BFX-90°-3000-F-JIC-1"1/2-B*	210	38	1"5/8-12 1"7/8-12	69.8	35.7	31 37	63 66	25	20	M 12 ou M 14*	1/2"
(1)Pressure max. recommended Flanges with 0'Ring and bolts Protection : Yellow galvanized For metric bolts, add "M" after the reference ; for UNC bolts, add "U". * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

90° PORT ASSEMBLY FLANGES MALE UNF THREAD (JIC 74°) S.A.E. 6000 –/ ISO 6162-2
Part N°	PN bar¹	DN	Ø F	Q	GG	D	E	H	L	Bolts
										Metric	UNC
BFX-90°-6000-F-JIC-1/2"-A BFX-90°-6000-F-JIC-1/2"-B BFX-90°-6000-F-JIC-1/2"-C	350	13	3/4"-16 7/8"-14 1"1/16-12	40.5	18.2	17 17 20	40 42 43	16	14	M 8	5/16"
BFX-90°-6000-F-JIC-3/4"-A BFX-90°-6000-F-JIC-3/4"-B BFX-90°-6000-F-JIC-3/4"-C		19	7/8"-14 1"1/16-12 1"5/16-12	50.8	23.8	20 20 25	49 51 52	19	14	M 10	3/8"
BFX-90°-6000-F-JIC-1"-A BFX-90°-6000-F-JIC-1"-B BFX-90°-6000-F-JIC-1"-C		25	1"1/16-12 1"5/16-12 1"5/8-12	57.2	27.8	25 25 31	55 56 58	24	18	M 12	7/16"
	250
BFX-90°-6000-F-JIC-1"1/4-A* BFX-90°-6000-F-JIC-1"1/4-B* BFX-90°-6000-F-JIC-1"1/4-C*		32	1"5/16-12 1"5/8-12 1"7/8-12	66.6	31.8	31 31 37	56 63 63	25	18	M 14 *	1/2"
BFX-90°-6000-F-JIC-1"1/2-A BFX-90°-6000-F-JIC-1"1/2-B		38	1"5/8-12 1"7/8-12	79.3	36.5	37 37	67 70	26	20	M 16	5/8"
(1)Pressure max. recommended Flanges with 0'Ring and bolts Protection : Yellow galvanized For metric bolts, add "M" after the reference ; for UNC bolts, add "U". * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

Test port square

Union assembly

BRIDES DE LIAISON BUTT WELDING A PASSAGE INTEGRAL - SAE 3000 / SAE 6000

UNION ASSEMBLY FLANGES BUTT WELDING S.A.E. 3000 – ISO 6162-1
Part N°	PN bar¹	DN	For tube diameter to... at ...	Ø A	Ø H1	L	FF	O	GG	Q	Bolts Metric
BL-3000-BWI-3/8" ** BL-3000-BWI-1/2"	350	10 13	14 -18 18 -22	12 13	18 22	80 90	40 46	50 54	16.5 17.5	35 38.1	M 8X45 M 8X40
BL-3000-BWI-3/4"	350	19	25 - 28	19	28	100	52	65	22.3	47.6	M 10X40
BL-3000-BWI-1" BL-3000-BWI-1"1/4 *	315	25 32	30 - 35 38 - 43	25 32	35 43	110 120	59 73	70 79.5	26.2 30.2	52.4 58.7	M 10X45 M 12X45*
BL-3000-BWI-1" BL-3000-BWI-1"1/4 *	250	25 32	30 - 35 38 - 43	25 32	35 43	110 120	59 73	70 79.5	26.2 30.2	52.4 58.7	M 10X45 M 12X45*
BL-3000-BWI-1"1/2 *	210	38	48 - 50	38	50	130	83	94	35.7	69.8	M 14X50 *
BL-3000-BWI-2" * BL-3000-BWI-2"1/2 *	210	51 64	60 - 63 73 - 76	47 58	61.8 74	140 150	97 109	102 114.5	42.9 50.8	77.8 88.9	M 14X50 * M 14X55 *
BL-3000-BWI-2" * BL-3000-BWI-2"1/2 *	160	51 64	60 - 63 73 - 76	47 58	61.8 74	140 150	97 109	102 114.5	42.9 50.8	77.8 88.9	M 14X50 * M 14X55 *
BL-3000-BWI-3"	138	76	88 - 90	70	90	170	131	135	61.9	106.4	M 16X65
BL-3000-BWI-3"1/2 BL-3000-BWI-4"	35	89 102	95 - 102 113 - 120	86 96	102 114	180 200	140 152	152 162	69.8 77.8	120.7 130.2	M 16X65 M 16X70
(1)Pressure max. recommended Flanges with 0'Ring and metric bolds. ** In 3/8" undivided split flanges in drawn steel not wrought * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order.

UNION ASSEMBLY FLANGES BUTT WELDING S.A.E. 6000 – ISO 6162-2
Part N°	PN bar¹	DN	For tube diameter to... at ...	Ø A	Ø H1	L	FF	O	GG	Q	Bolts Metric
BL-6000-BWI-1/2" BL-6000-BWI-3/4"	400	13 19	20 - 22 25 - 28	13 17.5	22 28	90 100	48 60	56.5 71	18.2 23.8	40.5 50.8	M 8X45 M 10X50
BL-6000-BWI-1"		25	30 - 35	22	35	110	70	81	27.8	57.2	M 12X65
BL-6000-BWI-1"1/4 * BL-6000-BWI-1"1/2		32 38	38 - 43 48 - 52	29 35	43.8 50.6	120 130	78 95	95 113	31.8 36.5	66.6 79.3	M 14X70 * M 16X80
BL-6000-BWI-2"		51	60 - 65	43	65	140	114	133	44.5	96.8	M 20X100
(1)Pressure max. recommended Flanges with 0'Ring and metric bolds. ** In 3/8" undivided split flanges in drawn steel not wrought * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order.

UNION ASSEMBLY FLANGES BUTT WELDING REDUCING - SAE 3000 / SAE 6000

UNION ASSEMBLY FLANGES REDUCING SOCKET WELDING - SAE 3000 / SAE 6000

BRIDES DE LIAISON SOCKET WELDING A PASSAGE REDUIT

UNION ASSEMBLY FLANGES REDUCING SOCKET WELDING S.A.E. 3000 – ISO 6162-1
Part N°	PN Bar¹	DN	Outer diameter tube			ØL1	ØL2	ØA	K	L	GG	Q	FF	O	Bolts Metric
Part N°	PN Bar¹	DN	MM	GAZ	SCHD	ØL1	ØL2	ØA	K	L	GG	Q	FF	O	Bolts Metric
BL-3000-SWR-1/2"-16.5 BL-3000-SWR-1/2"-17.6	315	13	16	16,75	17.14	16.5 17.6	24	12	12	70	17.5	38.1	46	54	M 8X40
BL-3000-SWR-3/4"-18.5 BL-3000-SWR-3/4"-20.5 BL-3000-SWR-3/4"-21.7		19	18 20	21.25	21.34	18.5 20.5 21.7	31.5	13	13	80	22.3	47.6	52	65	M 10X40
BL-3000-SWR-1"-25.5 BL-3000-SWR-1"-27.3		25	25	26.75	26.68	25.5 27.3	38	19	14	90	26.2	52.4	59	70	M 10X45
BL-3000-SWR-1"1/4-30.5* BL-3000-SWR-1"1/4-32.5* BL-3000-SWR-1"1/4-34* BL-3000-SWR-1"1/4-35.5*	200	32	30 32 35	33.50	33.50	30.5 32.5 34 35.5	43	25	16	100	30.2	58.7	73	79.5	M 12X45*
BL-3000-SWR-1"1/2-38.5* BL-3000-SWR-1"1/2-40.7* BL-3000-SWR-1"1/2-43*		38	38 40 42	42.25	42.16	38.5 40.7 43	50	32	18	110	35.7	69.8	83	94	M 14X50*
BL-3000-SWR-2"-49* BL-3000-SWR-2"-50.7*		51	50	48.25	48.26	49 50.7	61.8	38	20	130	42.9	77.8	97	102	M 14X50*
BL-3000-SWR-2"1/2-61* BL-3000-SWR-2"1/2-65.8*	150	64	60 65	60.30	60.30	61 65.8	73.8	47	22	150	50.8	88.9	109	114.5	M 14X55*
BL-3000-SWR-3"-74 BL-3000-SWR-3"-77	100	76		76.10	73.02	74 77	90	58	24	170	61.9	106.4	131	135	M 16X65
BL-3000-SWR-3"-81	100		80			81
(1)Pressure max. recommended Flanges with 0'Ring and metric bold. * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order.

UNION ASSEMBLY FLANGES REDUCING SOCKET WELDING S.A.E. 6000 – ISO 6162-2
Part N°	PN Bar¹	DN	Outer diameter tube			ØL1	ØL2	ØA	K	L	GG	Q	FF	O	Bolts Metric
Part N°	PN Bar¹	DN	MM	GAZ	SCHD	ØL1	ØL2	ØA	K	L	GG	Q	FF	O	Bolts Metric
BL-6000-SWR-1/2"-16.5 BL-6000-SWR-1/2"-17.6	380	13	16	16,75	17.14	16.5 17.6	24	11	13	70	18.2	40.5	48	56.5	M 8X45
BL-6000-SWR-3/4"-18.5 BL-6000-SWR-3/4"-20.5 BL-6000-SWR-3/4"-21.7		19	18 20	21.25	21.34	18.5 20.5 21.7	31.8	13	13	80	23.8	50.8	60	71	M 10X50
BL-6000-SWR-1"-25.5 BL-6000-SWR-1"-27.3		25	25	26.75	26.68	25.5 27.3	38	17.5	13	90	27.8	57.2	70	81	M 12X65
BL-6000-SWR-1"1/4-30.5* BL-6000-SWR-1"1/4-32.5* BL-6000-SWR-1"1/4-34*	300	32	30 32	33.50	33.40	30.5 32.5 34	44	22	16	100	31.8	66.6	78	95	M 14X70
BL-6000-SWR-1"1/4-35.5*		32	35			35.5	44	22	16	100	31.8	66.6	78	95	M 14X70
BL-6000-SWR-1"1/2-38.5			38			38.5
BL-6000-SWR-1"1/2-40.5 BL-6000-SWR-1"1/2-42.8		38	40 42	42.25	42.16	40.5 42.8	51	29	18	110	36.5	79.3	95	113	M 16X80
BL-6000-SWR-2"-49 BL-6000-SWR-2"-50.8		51	50	48.25	48.26	49 50.8	67	35	20	130	44.5	96.8	114	133	M 20X100
(1)Pressure max. recommended Flanges with 0'Ring and metric bold. * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order.

UNION ASSEMBLY FLANGES SOCKET WELD TUBE END - SAE 3000

Port assembly shutter

PORT ASSEMBLY SHUTTER FLANGES WITH PLUGS - SAE 3000 / SAE 6000

BLANKS SHUTTER - SAE 3000 / SAE 6000

BLANKS SHUTTER FLANGES - S.A.E. 3000 – ISO 6162-1
Part N°	PN bar1	DN	GG	Q	FF	O	E	F	Ø H*	Bolts
										Metric	UNC
BFX-OB-MONO-3000-1/2"	350	13	17.5	38.1	47	57	16	14	10	M 8	5/16"
BFX-OB-MONO-3000-3/4"		19	22.3	47.6	49	66	18	16	15	M 10	3/8"
BFX-OB-MONO-3000-1"	315	25	26.2	52.4	53	71	19	16	18	M 10	3/8"
BFX-OB-MONO-3000-1"1/4 *	250	32	30.2	58.7	69	80	21	18	23	M 10 ou M 12	7/16"
BFX-OB-MONO-3000-1"1/2 *	210	38	35.7	69.8	77	95	24	19	28	M 12 ou M 14	1/2"
BFX-OB-MONO-3000-2" *		51	42.9	77.8	89	103	24	19	45	M 12 ou M 14	1/2"
BFX-OB-MONO-3000-2"1/2 *	160	64	50.8	88.9	101	116	25	19	58	M 12 ou M 14	1/2"
BFX-OB-MONO-3000-3"	138	76	61.9	106.4	124	136	25	27	70	M 16	5/8"
BFX-OB-MONO-3000-3"1/2	35	89	69.8	120.7	136	152	25	27	85	M 16	5/8"
BFX-OB-MONO-3000-4"	35	102	77.8	130.2	146	162	25	27	95	M 16	5/8"
BFX-OB-MONO-3000-5"	35	127	92	152.4	180	184	25	27	110	M 16	5/8"
(1)Pressure max. recommended Flanges with 0'Ring and metric bolts. For metric bolts, add "M" after the reference ; for UNC bolts, add "U". Standard delivered with undivided split flanges, specify for split flanges. *On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

BLANKS SHUTTER FLANGES - S.A.E. 6000 – ISO 6162-2
Part N°	PN bar1	DN	GG	Q	FF	O	E	F	Ø H*	Bolts
										Metric	UNC
BFX-OB-MONO-6000-1/2"	400	13	18.2	40.5	47	57	16	14	10	M 8	5/16"
BFX-OB-MONO-6000-3/4"		19	23.8	50.8	53	71	19	16	15	M 10	3/8"
BFX-OB-MONO-6000-1"		25	27.8	57.2	66	80	24	18	22	M 12	7/16"
BFX-OB-MONO-6000-1"1/4 *		32	31.8	66.6	77	94	27	24	30	M 14 ou M12	1/2"
BFX-OB-MONO-6000-1"1/2		38	36.5	79.3	89	103	30	24	35	M 16	5/8"
BFX-OB-MONO-6000-2"		51	44.5	96.8	123	135	35	31	48	M 20	3/4"
(1)Pressure max. recommended Flanges with 0'Ring and metric bolts. For metric bolts, add "M" after the reference ; for UNC bolts, add "U". Standard delivered with undivided split flanges, specify for split flanges. *On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

Counter flanges

BRIDES SANS GORGE TARAUDÉES BSPP OU NPT - SAE 3000 / SAE 6000

COUNTER FLANGES FEMALE BSPP THREADOR NPT S.A.E. 3000 –ISO 6162-1
Part N°	PN bar¹	DN	Ø F BSP	ØA	L	GG	Q	FF	O	U	K	Bolts
Part N°	PN bar¹	DN	Ø F BSP	ØA	L	GG	Q	FF	O	U	K	Metric	UNC
BAS-3000-T-BSP-1/2"	345	13	1/2"	13	36	17.5	38.1	47	57	16	19	M 8	5/16"
BAS-3000-T-BSP-3/4"		19	3/4"	19	36	22.3	47.6	49	66	18	19	M 10	3/8"
BAS-3000-T-BSP-1"		25	1"	25	38	26.2	52.4	53	71	18	19	M 10	3/8"
BAS-3000-T-BSP-1"1/4 *	278	32	1"1/4	31	41	30.2	58.7	69	80	21	22	M 10 ou M 12*	7/16"
BAS-3000-T-BSP-1"1/2 *	210	38	1"1/2	38	44	35.7	69.8	77	94	25	24	M 12 ou M 14*	1/2"
BAS-3000-T-BSP-2" *	210	51	2"	50	45	42.9	77.8	89	103	25	26	M 12 ou M 14*	1/2"
BAS-3000-T-BSP-2"1/2 *	175	64	2"1/2	63	50	50.8	88.9	101	115	25	30	M 12 ou M 14*	1/2"
BAS-3000-T-BSP-3"	138	76	3"	73	50	61.9	106.4	124	135	27	34	M 16	5/8"
BAS-3000-T-BSP-3"1/2	35	89	3"1/2	89	50	69.8	120.7	136	152	27	30	M 16	5/8"
BAS-3000-T-BSP-4"	35	102	4"	99	50	77.8	130.2	146	162	27	30	M 16	5/8"
(1)Pressure max. recommended For metric bolts, add "M" after the reference ; for UNC bolts, add "U". For tapped NPT, replace BSP by NPT into the reference. * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

COUNTER FLANGES FEMALE BSPP THREADOR NPT S.A.E. 6000 – ISO 6162-2
Part N°	PN bar¹	DN	Ø F BSP	ØA	L	GG	Q	FF	O	U	K	Bolts
Part N°	PN bar¹	DN	Ø F BSP	ØA	L	GG	Q	FF	O	U	K	Metric	UNC
BAS-6000-T-BSP-1/2"	400	13	1/2"	13	36	18.2	40.5	47	57	16	19	M 8	5/16"
BAS-6000-T-BSP-3/4"		19	3/4"	19	36	23.8	50.8	53	71	19	22	M 10	3/8"
BAS-6000-T-BSP-1"		25	1"	25	44	27.8	57.2	69	80	24	24	M 12	7/16"
BAS-6000-T-BSP-1"1/4 *		32	1"1/4	31	44	31.8	66.6	77	94	27	25	M 14 ou M 12*	1/2"
BAS-6000-T-BSP-1"1/2		38	1"1/2	38	51	36.5	79.3	89	106	30	28	M 16	5/8"
BAS-6000-T-BSP-2"		51	2"	50	70	44.5	96.8	116	135	37	33	M 20	3/4"
(1)Pressure max. recommended For metric bolts, add "M" after the reference ; for UNC bolts, add "U". For tapped NPT, replace BSP by NPT into the reference. * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

COUNTER FLANGES BUTT WELDING TUBE END (MONOBLOC) BWI - SAE 3000 / SAE 6000

COUNTER FLANGES BUTT WELDING TUBE END (MONOBLOC) BWI S.A.E. 3000 –ISO 6162-1
Part N°	PN bar¹	DN	ØA	ØB	L	GG	Q	FF	U	O	Bolts
Part N°	PN bar¹	DN	ØA	ØB	L	GG	Q	FF	U	O	Metric	UNC
BAS-MATRI-3000- BWI-1/2"-21.5	345	13	21.6	13	36	17.5	38	47	16	57	M 8	5/16"
BAS-MATRI-3000-BWI-3/4"-27	345	19	27.2	19	36	22.3	47.6	49	18	66	M 10	3/8"
BAS-MATRI-3000-BWI-1"-34	315	25	34.5	25	38	26.2	52.4	53	18	71	M 10	3/8"
BAS-MATRI-3000-BWI-1"1/4-42*	250	32	42.8	31	41	30.2	58.7	69	21	80	M 10 ou M 12*	7/16"
BAS-MATRI-3000-BWI-1"1/2-48.6*	210	38	48.6	38	44	35.7	69.8	77	25	94	M 12 ou M 14*	1/2"
BAS-MATRI-3000-BWI-2"-61*	210	51	61	50	45	42.9	77.8	89	25	103	M 12 ou M 14*	1/2"
BAS-MATRI-3000-BWI-2"1/2-77*	160	64	76.6	63	50	50.8	88.9	101	25	115	M 12 ou M 14*	1/2"
BAS-MATRI-3000-BWI-3"-90.5	138	76	89	73	50	61.9	106.4	124	27	135	M 16	5/8"
BAS-MATRI-3000-BWI-3"1/2-103	35	89	103	89	50	70	120.7	137	27	153	M 16	5/8"
BAS-MATRI-3000-BWI-4"-115	35	102	115	99	50	77.8	130	147	27	163	M 16	5/8"
(1)Pressure max. recommended For metric bolts, add "M" after the reference ; for UNC bolts, add "U". * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

COUNTER FLANGES BUTT WELDING TUBE END (MONOBLOC) BWI S.A.E. 6000 – ISO 6162-2
Part N°	PN bar¹	DN	ØA	ØB	L	GG	Q	FF	U	O	Bolts
Part N°	PN bar¹	DN	ØA	ØB	L	GG	Q	FF	U	O	Metric	UNC
BAS-MATRI-6000-BWR-1/2"-17.5	400	13	17.5	10	36	18.2	40.5	47	16	57	M 8	5.16"
BAS-MATRI-6000-BWI-1/2"-21.6		13	21.6	13	36	18.2	40.5	47	16	57	M 8	5/16"
BAS-MATRI-6000-BWI-3/4"-27.2		19	27.2	18	36	23.8	50.8	53	19	71	M 10	3/8"
BAS-MATRI-6000-BWI-1"-34.5		25	34.5	22	44	27.8	57.2	66	24	80	M 12	7/16"
BAS-MATRI-6000-BWI-1"1/4-42.8*		32	42.8	28	44	31.6	66.7	77	27	94	M 14*	1/2"
BAS-MATRI-6000-BWI-1"1/2-48.6		38	48.6	32	51	36.7	79.4	89	30	106	M 16	5/8"
BAS-MATRI-6000-BWI-2"-61		51	61	41	58	44.4	96.8	116	37	135	M 20	3/4"
(1)Pressure max. recommended For metric bolts, add "M" after the reference ; for UNC bolts, add "U". * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

COUNTER FLANGES SWI (MONOBLOC) - SAE 3000 / SAE 6000

CONTER FLANGES SOCKET WELD TUBE END - SAE 3000

Blocks

BLOCS EQUERRES DE FIXATION - SAE 3000 / SAE 6000

L BLOCKS - SAE 3000 / SAE 6000

T BLOCKS - SAE 3000 / SAE 6000

X BLOCKS - SAE 3000 / SAE 6000

Square flanges - PN 250/ PN 400

Square flanges

SQUARE FLANGES CETOP-SIDERURGIE - PN 250 / CETOP

SQUARE FLANGES CETOP-SIDERURGIE - PN 400 / CETOP

Port assembly

PORT ASSEMBLY FLANGES BUTT WELDING CETOP-SIDERURGIE - PN250 / PN400

BRIDES DE FIXATION BUTT WELDING INTEGRAL CETOP SIDERURGIE

PORT ASSEMBLY FLANGES BUTT WELDING CETOP-SIDERURGIE PN 250* / CETOP
Part N°	PN bar¹	DN	For tube diameter to... at ...	Ø A	Ø H1	L	0	GG	Bolts Metric
BFX-250-BWI-CET-3/8" BFX-250-BWI-CET-1/2"	250	10 13	14 - 18 18 - 22	12 13	18 22	40 45	40 45	24.7 29.7	6 X 25 8 X 30
BFX-250-BWI-SID-1/2"		13	18 - 22	13	22	45	45	30	6 X 25
BFX-250-BWI-CET-SID-3/4 BFX-250-BWI-CET-SID-1"		19 25	25 - 28 30 - 35	19 25	28 35	50 55	50 65	35.3 43.8	8 X 30 10 X 35
BFX-250-BWI-CET-SID-1"1/4		32	38 - 42.3	32	43	60	75	51.6	12 X 45
BFX-250-BWI-CET-1"1/2 BFX-250-BWI-SID-1"1/2		38 38	48 - 50 48 - 50	38 38	50 50	65 65	85 85	60 60	14 X 50 12 X 50
BFX-250-BWI-CET-2"		51	60 - 63.3	47	62	70	100	69.4	16 X 55
BFX-250-BWI-SID-2" BFX-250-BWI-CET-2"1/2		51 56	60 - 63.3 73 - 80	47 58	62 76	70 75	100 120	68 83.4	14 X 55 20 X 70
BFX-250-BWI-SID-2"1/2		56	73 - 80	58	76	75	120	85	18 X 70
BFX-250-BWI-CET-3" BFX-250-BWI-SID-3"		63 63	88 - 90 88 - 90	70 70	90 90	85 85	140 140	102.5 95	20 X 75 22 X 80
BFX-250-BWI-CET-3"1/2		70	95 - 102	77	102	90	140	102.5	20 X 90
BFX-250-BWI-CET-4" BFX-250-BWI-SID-4"		80 80	113 - 120 113 - 120	90 90	118 118	100 100	160 180	113.2 130	24 X 100 27 X 100
(1)Pressure max. recommended Flanges with 0'Ring and metric bolts. On request can be delivered with ISO 6164

PORT ASSEMBLY FLANGES BUTT WELDING CETOP-SIDERURGIE PN 400* / CETOP
Part N°	PN bar¹	DN	For tube diameter to... at ...	Ø A	Ø H1	L	0	GG	Bolts Metric
BFX-400-BWI-CET-3/8" BFX-400-BWI-CET-1/2"	400	10 13	16 - 18 20 - 22	11 13	17.5 22	40 45	40 45	24.7 29.7	6 X 25 8 X 30
BFX-400-BWI-CET-3/4"		19	25 - 28	17.5	28	50	50	35.3	8 X 35
BFX-400-BWI-CET-1" BFX-400-BWI-CET-1"1/4		25 32	33 - 35 42 - 45	22 29	35 43.8	55 60	65 75	43.8 51.6	10 X 40 12 X 45
BFX-400-BWI-CET-1"1/2		38	48 - 51	35	50.6	65	85	60	14 X 55
BFX-400-BWI-CET-2" BFX-400-BWI-CET-2"1/2		51 56	60 - 65 75 - 80	43 53	65 76	70 80	100 120	69.4 83.4	16 X 65 20 X 80
BFX-400-BWI-CET-3"		63	80 - 90	58	90	90	140	102.5	20 X 90
BFX-400-BWI-CET-3"1/2 BFX-400-BWI-CET-4"		70 80	90 - 102 110 - 120	63 74	102 118	90 110	140 160	102.5 113.2	20 X 90 24 X 100
(1)Pressure max. recommended Flanges with 0'Ring and metric bolts. On request can be delivered with ISO 6164

PORT ASSEMBLY FLANGES REDUCING BUTT WELDING CETOP-SIDERURGIE - PN250 / PN400

BRIDES DE LIAISON BUTT WELDING PASSAGE REDUIT CETOP SIDERURGIE

PORT ASSEMBLY FLANGES REDUCING BUTT WELDING CETOP-SIDERURGIE PN 250* / CETOP
Part N°	PN bar¹	DN	For tube diameter to... at ...	Ø A	Ø H1	L	0	GG	Bolts Metric
BFX-250-BWR-CET-1/2" BFX-250-BWR-SID-1/2"	250	13 13	14 - 18 14 - 18	12 12	18 18	45 45	45 45	29.7 30	8 X 30 6 X 25
BFX-250-BWR-CET-SID-3/4"		19	16 - 22	13	22	50	50	35.3	8 X 30
BFX-250-BWR-CET-SID-1" BFX-250-BWR-CET-SID-1"1/4		25 32	25 - 28 30 - 35	19 25	28 35	55 60	65 75	43.8 51.6	10 X 35 12 X 45
BFX-250-BWR-CET-1"1/2		38	38 - 43	32	43	65	85	60	14 X 50
BFX-250-BWR-SID-1"1/2 BFX-250-BWR-CET-2"		38 51	38 - 43 48 - 50	32 38	43 50	65 70	85 100	60 69.4	12 X 50 16 X 55
BFX-250-BWR-SID-2"		51	48 - 50	38	50	70	100	68	14 X 55
BFX-250-BWR-CET-2"1/2 BFX-250-BWR-SID-2"1/2		56 56	60 - 63 60 - 63	47 47	62 62	75 75	120 120	83.4 85	20 X 70 18 X 70
BFX-250-BWR-CET-3"		63	73 -80	58	76	85	140	102.5	20 X 75
BFX-250-BWR-SID-3" BFX-250-BWR-CET-3"1/2		63 70	73 - 80 88 - 90	58 70	76 90	85 90	140 140	95 102.5	22 X 75 20 X 90
BFX-250-BWR-CET-4"		80	95 - 102	80	102	100	160	113.2	24 X 100
BFX-250-BWR-SID-4"		80	95 - 102	80	102	100	180	130	27 X 100
(1)Pressure max. recommended Flanges with 0'Ring and metric bolts. On request can be delivered with ISO 6164

PORT ASSEMBLY FLANGES REDUCING BUTT WELDING CETOP-SIDERURGIE PN 400* / CETOP
Part N°	PN bar¹	DN	For tube diameter to... at ...	Ø A	Ø H1	L	0	GG	Bolts Metric
BFX-400-BWR-CET-1/2" BFX-400-BWR-CET-3/4"	400	13 19	16 - 18 20 - 22	11 13	17.5 22	45 50	45 50	29.7 35.3	8 X 30 8 X 35
BFX-400-BWR-CET-1"		25	25 - 28	17.5	28	55	65	43.8	10 X 40
BFX-400-BWR-CET-1"1/4 BFX-400-BWR-CET-1"1/2		32 38	30 - 35 38 - 43	22 29	35 43.8	60 65	75 85	51.6 60	12 X 45 14 X 55
BFX-400-BWR-CET-2"		51	48 - 51	35	50.6	65	100	69.4	16 X 65
BFX-400-BWR-CET-2"1/2 BFX-400-BWR-CET-3"		56 63	60 - 65 75 - 80	43 53	65 80	70 90	120 140	83.4 102.5	20 X 80 20 X 90
BFX-400-BWR-CET-3"1/2		70	88 - 90	58	90	90	140	102.5	20 X 90
BFX-400-BWR-CET-4"		80	100 - 102	63	102	110	160	113.2	24 X 100
(1)Pressure max. recommended Flanges with 0'Ring and metric bolts. On request can be delivered with ISO 6164

PORT ASSEMBLY FLANGES FEMALE BSP/NPT THREAD CETOP-SIDERURGIE - PN250 / PN400

PORT ASSEMBLY FLANGES FEMALE BSP/NPT THREAD CETOP-SIDERURGIE PN 250* / CETOP
Part N°	PN bar¹	DN	Ø F	Ø A	K	L	O	GG	Bolts Metric
BFX-250-T-BSP-CET-3/8"-A BFX-250-T-BSP-CET-3/8"-B	250	10	3/8" 1/4"	12 10	13 12	23	40	24.7	M 6X25
BFX-250-T-BSP-CET-1/2"-A		13	1/2"	14	15	32	45	29.7	M 8X35
BFX-250-T-BSP-CET-1/2"-B		13	3/8"	13	13	32	45	29.7	M 8X35
BFX-250-T-BSP-SID-1/2"-A BFX-250-T-BSP-SID-1/2"-B		13	1/2" 3/8"	14 13	15 13	32	45	30	M 6X35
BFX-250-T-BSP-CET-SID-3/4"-A		19	3/4"	20	18	32	50	35.3	M 8X35
BFX-250-T-BSP-CET-SID-3/4"-B		19	1/2"	18	15	32	50	35.3	M 8X35
BFX-250-T-BSP-CET-SID-1"-A BFX-250-T-BSP-CET-SID-1"-B		25	1" 3/4"	25 22	20 18	36	65	43.8	M 10X40
BFX-250-T-BSP-CET-SID-1"1/4-A		32	1"1/4	32	22	38	75	51.6	M 12X45
BFX-250-T-BSP-CET-SID-1"1/4-B		32	1"	28	20	38	75	51.6	M 12X45
BFX-250-T-BSP-CET-1"1/2-A BFX-250-T-BSP-CET-1"1/2 B		38	1"1/2 1"1/4	38 36	24 22	42	85	60	M 14X50
BFX-250-T-BSP-SID-1"1/2-A		38	1"1/2	38	24	42	85	60	M 12X50
BFX-250-T-BSP-SID-1"1/2-B		38	1"1/4	36	22	42	85	60	M 12X50
BFX-250-T-BSP-CET-2"-A BFX-250-T-BSP-CET-2"-B		51	2" 1"1/2	47 43	27 24	44	100	69.4	M 16X55
BFX-250-T-BSP-SID-2"-A		51	2"	47	27	44	100	68	M 14X50
BFX-250-T-BSP-SID-2"-B		51	1"1/2	43	24	44	100	68	M 14X50
(1)Pressure max. recommended Flanges with 0'Ring and metric bolts. For threaded NPT, replace T BSP by T NPT into the reference. On request can be delivered with ISO 6164

PORT ASSEMBLY FLANGES FEMALE BSP/NPT THREAD CETOP-SIDERURGIE PN 400* / CETOP
Part N°	PN bar¹	DN	Ø F	Ø A	K	L	O	GG	Bolts Metric
BFX-400-T-BSP-CET-3/8"-A BFX-400-T-BSP-CET-3/8"-A	400	10	3/8" 1/4"	12 10	13 12	23	40	24.7	M 6X25
BFX-400-T-BSP-CET-1/2"-A		13	1/2"	14	15	32	45	29.7	M 8X35
BFX-400-T-BSP-CET-1/2"-B		13	3/8"	13	13	32	45	29.7	M 8X35
BFX-400-T-BSP-CET-3/4"-A BFX-400-T-BSP-CET-3/4"-B		19	3/4" 1/2"	20 18	18 15	32	50	35.3	M 8X35
BFX-400-T-BSP-CET-1"-A		25	1"	25	18	36	65	43.8	M 10X40
BFX-400-T-BSP-CET-1"-B		25	3/4"	22	20	36	65	43.8	M 10X40
BFX-400-T-BSP-CET-1"1/4-A BFX-400-T-BSP-CET-1"1/4-B		32	1"1/4 1"	32 28	22 20	38	75	51.6	M 12X45
BFX-400-T-BSP-CET-1"1/2-A		38	1"1/2	38	24	42	85	60	M 14X50
BFX-400-T-BSP-CET-1"1/2-B		38	1"1/4	36	22	42	85	60	M 14X50
BFX-400-T-BSP-CET-2"-A BFX-400-T-BSP-CET-2"B		51	2" 1"1/2	47 43	27 24	44	100	69.4	M 16X55
(1)Pressure max. recommended Flanges with 0'Ring and metric bolts. For threaded NPT, replace T BSP by T NPT into the reference. On request can be delivered with ISO 6164

BRIDES DE FIXATION SOCKET WELDING INTÉPORT ASSEMBLY FLANGES SOCKET WELDING CETOP-SIDERURGIE - PN 250

90° PORT ASSEMBLY FLANGES BW CETOP-SIDERURGIE - PN250 / PN400

T BLOCKS BW CETOP-SIDERURGIE - PN250 / PN400

Test port square

Union assembly

UNION ASSEMBLY FLANGES REDUCING SOCKET WELDING CETOP-SIDERURGIE - PN250 / PN400

UNION ASSEMBLY FLANGES REDUCING SOCKET WELDING CETOP-SIDERURGIE PN 250* / CETOP
Part N°	PN bar¹	DN	For tube diameter to .... at ....	Ø A	Ø H1	L	O	GG	Bolts Metric
BL-250-BWR-CET-1/2" BL-250-BWR-SID-1/2"	250	13 13	14 - 18 14 - 18	12 12	17.5 18	90 90	45 45	29.7 30	8 X 45 6 X40
BL-250-BWR-CET-SID-3/4"		19	18 - 22	13	22	100	50	35.3	8 X 45
BL-250-BWR-CET-SID-1" BL-250-BWR-CET-SID-1"1/4		25 32	25 - 28 30 - 35	20 25	28 35	110 120	65 75	43.8 51.6	10 X 50 12 X 60
BL-250-BWR-CET-1"1/2		38	38 - 43	32	43	130	85	60	14 X 70
BL-250-BWR-SID-1"1/2		38	38 - 43	32	43	130	85	60	12 X 70
BL-250-BWR-CET-2" BL-250-BWR-SID-2"		51 51	48 - 50 48 - 50	38 38	50 50	140 140	100 100	69.4 68	16 X 75 14 X 75
BL-250-BWR-CET-2"1/2		56	60 - 63	47	62	150	120	83.4	18 X 100
BL-250-BWR-SID-2"1/2		56	60 - 63	47	62	150	120	85	20 X 100
BL-250-BWR-CET-3" BL-250-BWR-CET-3"1/2		63 70	73 - 76 88 - 90	56 70	76 90	70 180	140 140	102.5 102.5	20 X 110 20 X 130
BL-250-BWR-CET-4"		80	95 - 102	80	102	200	160	113.2	24 X 150
BL-250-BWR-SID-4"		80	95 - 102	80	102	200	180	130	27 X 150
(1)Pression maxi. recommandée Flanges with 0'Ring and metric bolts. On request can be delivered with ISO 6164.

UNION ASSEMBLY FLANGES REDUCING SOCKET WELDING CETOP-SIDERURGIE PN 400* / CETOP
Part N°	PN bar¹	DN	For tube diameter to .... at ....	Ø A	Ø H1	L	O	GG	Bolts Metric
BL-400-BWR-CET-1/2" BL-400-BWR-CET-3/4"	400	13 19	16 - 18 20 - 22	12 13	17.5 22	90 100	45 50	29.7 35.3	8 X 45 8 X 55
BL-400-BWR-CET-1"		25	25 - 28	17.5	28	110	65	43.8	10 X 60
BL-400-BWR-CET-1"1/4 BL-400-BWR-CET-1"1/2		32 38	30 - 35 38 - 43	22 29	35 43.8	120 130	75 85	51.6 60	12 X 70 14 X 80
BL-400-BWR-CET-2"		51	48 - 51	35	51	130	100	69.4	16 X 100
BL-400-BWR-CET-2"1/2 BL-400-BWR-CET-3"		56 63	60 - 65 73 - 76	43 53	65 80	140 180	120 140	83.4 102.5	20 X 120 20 X 130
BL-400-BWR-CET-3"1/2		70	88 - 90	58	90	180	140	102.5	20 X 140
BL-400-BWR-CET-4"		80	95 - 102	63	102	220	160	113.2	24 X 150
(1)Pression maxi. recommandée Flanges with 0'Ring and metric bolts. On request can be delivered with ISO 6164.

UNION ASSEMBLY FLANGES BUTT WELDING CET/SID - PN250 / PN400

BRIDES DE LIAISON BUTT WELDING INTEGRAL CETOP SIDERURGIE

UNION ASSEMBLY FLANGES BUTT WELDING CETOP-SIDERURGIE PN 250* / CETOP
Part N°	PN bar¹	DN	For tube diameter to .... at ....	Ø A	Ø H1	L	O	GG	Bolts Metric
BL-250-BWI-CET-3/8"	250	10	14 - 18	12	18	80	40	24.7	6 X 35
BL-250-BWI-CET-1/2"		13	18 - 22	13	22	90	45	29.7	8 X 45
BL-250-BWI-SID-1/2"		13	18 - 22	13	22	90	45	30	6 X 40
BL-250-BWI-CET-SID-3/4" BL-250-BWI-CET-SID-1"		19 25	25 - 28 30 - 35	19 25	28 35	100 110	50 65	35.3 43.8	8 X 45 10 X 50
BL-250-BWI-CET-SID-1"1/4		32	38 - 43	32	43	120	75	51.6	12 X 60
BL-250-BWI-CET-1"1/2 BL-250-BWI-SID-1"1/2		38 38	48 - 50 48 - 50	38 38	50 50	130 130	85 85	60 60	14 X 70 12 X 70
BL-250-BWI-CET-2"		51	60 - 63	47	62	140	100	69.4	16 X 75
BL-250-BWI-SID-2"		51	60 - 63	47	62	140	100	68	14 X 75
BL-250-BWI-CET-2"1/2 BL-250-BWI-SID-2"1/2		56 56	73 - 80 73 - 80	58 58	76 76	150 150	120 120	83.4 85	20 X 100 18 X 100
BL-250-BWI-CET-3"		63	88 - 90	70	90	170	140	102.5	20 X 110
BL-250-BWI-SID-3"		63	88 - 90	70	90	170	140	95	22 X 110
BL-250-BWI-CET-3"1/2 BL-250-BWI-CET-4" BL-250-BWI-SID-4"		70 80 80	95 - 102 113-120 113-120	77 90 90	102 118 118	180 200 200	140 160 180	102.5 113.2 130	20 X 130 24 X 150 27 X 150
(1)Pression maxi. recommandée Flanges with 0'Ring and metric bolts. On request can be delivered with ISO 6164.

UNION ASSEMBLY FLANGES BUTT WELDING CETOP-SIDERURGIE PN 400* / CETOP
Part N°	PN bar¹	DN	For tube diameter to .... at ....	Ø A	Ø H1	L	O	GG	Bolts Metric
BL-400-BWI-CET-3/8" BL-400-BWI-CET- 1/2"	400	10 13	16 - 18 20 - 22	11 13	17.5 22	80 90	40 45	24.7 29.7	6 X 45 8 X 50
BL-400-BWI-CET-3/4"		19	25 - 28	17.5	28	100	50	35.3	8 X 55
BL-400-BWI-CET-1" BL-400-BWI-CET-1"1/4		25 32	33 - 35 42 - 45	22 29	35 43.8	110 120	65 75	43.8 51.6	10 X 60 12 X 70
BL-400-BWI-CET-1"1/2		38	48 - 51	35	50.6	130	85	60	14 X 80
BL-400-BWI-CET-2" BL-400-BWI-CET-2"1/2		51 56	60 - 65 75 - 80	43 53	65 76	140 160	100 120	69.4 83.4	16 X 100 20 X 120
BL-400-BWI-CET-3"		63	88 - 90	58	90	180	140	102.5	20 X 130
BL-400-BWI-CET-3"1/2 BL-400-BWI-CET-4"		70 80	90 - 102 110 - 120	63 74	102 114	180 220	140 160	102.5 113.2	20 X 140 24 X 150
(1)Pression maxi. recommandée Flanges with 0'Ring and metric bolts. On request can be delivered with ISO 6164.

UNION ASSEMBLY FLANGES T - BW CETOP-SIDERURGIE - PN250 / PN400

Blank flanges

BLANK FLANGES CETOP-SIDERURGIE 2 PARTS - PN250 / PN400

BLANK FLANGES CETOP-SIDERURGIE - MONOBlOC - PN250 / PN400

Conter flanges

CONTER FLANGES FEMALE BSP/NPT THREAD CETOP-SIDERURGIE - PN250 / PN400

CONTER FLANGES FEMALE BSP/NPT THREAD CET/SID PN 250* / CETOP
Part N°	PN bar¹	DN	Ø F	Ø A	K	L	O	GG	Bolts
BAS-250-T-BSP-CET-3/8"-A BAS-250-T-BSP-CET-3/8"-B	250	10	3/8" 1/4"	12 10	13 12	23	40	24.7	M 6
BAS-250-T-BSP-CET-1/2"-A		13	1/2"	14	15	32	45	29.7	M 8
BAS-250-T-BSP-CET-1/2"-B			3/8"	13	13	32	45	29.7	M 8
BAS-250-T-BSP-SID-1/2"-A			1/2"	14	15	32	45	30	M 6
BAS-250-T-BSP-SID-1/2"-B			3/8"	13	13	32	45	30	M 6
BAS-250-T-BSP-CET-3/4"-A BAS-250-T-BSP-CET-3/4"-B		19	3/4" 1/2"	20 18	18 15	32	50	35.3	M 8
BAS-250-T-BSP-CET/SID-1"-A		25	1"	25	20	36	65	43.8	M 10
BAS-250-T-BSP-CET/SID-1"-B		25	3/4	22	18	36	65	43.8	M 10
BAS-250-T-BSP-CET/SID-1"1/4-A BAS-250-T-BSP-CET/SID-1"1/4-B		32	1"1/4 1"	32 28	22 20	38	75	51.6	M 12
BAS-250-T-BSP-CET-1"1/2-A		38	1"1/2	38	24	42	85	60	M 14
BAS-250-T-BSP-CET-1"1/2-B			1"1/4	36	22	42	85	60	M 14
BAS-250-T-BSP-SID-1"1/2-A			1"1/2	38	24	42	85	60	M 12
BAS-250-T-BSP-SID-1"1/2-B			1"1/4	36	22	42	85	60	M 12
BAS-250-T-BSP-CET-2"-A BAS-250-T-BSP-CET-2"-B		51	2" 1"1/2	47 43	27 24	44	100	69.4	M 16
BAS-250-T-BSP-SID-2"-A BAS-250-T-BSP-SID-2"-B		51	2" 1"1/2	47 43	27 24	44	100	68	M 14
(1)Pressure max. recommended For threaded NPT, replace T BSP by T NPT into the reference * On request can be delivered with ISO 6164

CONTER FLANGES FEMALE BSP/NPT THREAD CET/SID PN 400* / CETOP
Part N°	PN bar¹	DN	Ø F	Ø A	K	L	O	GG	Bolts
BAS-400-T-BSP-CET-3/8"-A BAS-400-T-BSP-CET-3/8"-B	400	10	3/8" 1/4"	12 10	13 12	23	40	24.7	M 6
BAS-400-T-BSP-CET-1/2"-A		13	1/2"	14	15	32	45	29.7	M 8
BAS-400-T-BSP-CET-1/2"-B		13	3/8"	13	13	32	45	29.7	M 8
BAS-400-T-BSP-CET-3/4"-A BAS-400-T-BSP-CET-3/4"-B		19	3/4" 1/2"	20 18	18 15	32	50	35.3	M 8
BAS-400-T-BSP-CET-1"-A		25	1"	25	20	36	65	43.8	M 10
BAS-400-T-BSP-CET-1"-B		25	3/4	22	18	36	65	43.8	M 10
BAS-400-T-BSP-CET-1"1/4-A BAS-400-T-BSP-CET-1"1/4-B		32	1"1/4 1"	32 28	22 20	38	75	51.6	M 12
BAS-400-T-BSP-CET-1"1/2-A		38	1"1/2	38	24	42	85	60	M 14
BAS-400-T-BSP-CET-1"1/2-B		38	1"1/4	36	22	42	85	60	M 14
BAS-400-T-BSP-CET-2"-A BAS-400-T-BSP-CET-2"-B		51	2" 1"1/2	47 43	27 24	44	100	69.4	M 16
(1)Pressure max. recommended For threaded NPT, replace T BSP by T NPT into the reference * On request can be delivered with ISO 6164

COUNTER FLANGES SOCKET WELDING CETOP-SIDERURGIE - PN250

Blocks

PORT ELBOW CETOP-SIDERURGIE - PN250 / PN400

L BLOCKS CETOP-SIDERURGIE
PN250 / PN400

T BLOCKS CETOP-SIDERURGIE
PN250 / PN400

Accessories for flanges

Flanged Head

FLANGED HEAD SOCKET WELDING (SWI) - SAE 3000 / SAE 6000

Collets socket welding a passage integral

FLANGED HEAD SOCKET WELDING (SWI) ISO 6162-1 - S.A.E. 3000
Part N°	DN	Outer diameter tube			Ø L1	Ø L2	Ø A	K	Ø C	L
Part N°	DN	MM	GAZ	SCHD	Ø L1	Ø L2	Ø A	K	Ø C	L
CAG-3000-SWI-1/2"-20.5 CAG-3000-SWI-1/2"-21.7	13	20	21.25	21.30	20.5 21.7	30	13	13	30.5	60
CAG-3000-SWI-3/4"-25.5 CAG-3000-SWI-3/4"-27.3	19	25	26.75	26.68	25.5 27.3	35	19	13	38.4	68
CAG-3000-SWI-1"-30.5 CAG-3000-SWI-1"-32.5 CAG-3000-SWI-1"-34 CAG-3000-SWI-1"-35.5	25	30 32 35	33.50	33.40	30.5 32.5 34 35.5	44	25	16	44.7	75
CAG-3000-SWI-1"1/4-38.5 CAG-3000-SWI-1"1/4-40.5 CAG-3000-SWI-1"1/4-43	32	38 40 42	42.25	42.16	38.5 40.5 43	55	32	18	51.1	95
CAG-3000-SWI-1"1/2-49 CAG-3000-SWI-1"1/2-50.4	38	48 50	48.25	48.26	49 50.4	63	38	20	60.6	100
CAG-3000-SWI-2"-61 CAG-3000-SWI-2"-65.8	51	60 65	60.3	60.32	61 65.8	79	47	22	71.4	107
CAG-3000-SWI-2"1/2-74 CAG-3000-SWI-2"1/2-77 CAG-3000-SWI-2"1/2-81	64	80	76.1	73.02	74 77 81	98	58	24	84.1	130
CAG-3000-SWI-3"-90.5	76	90		88.9	90.5	116	70	28	101.6	150
* SWI flanges head may only be fitted with split-flanges (the shoulder does not allow a one piece fitting to pass through). These references design groove flanged head for 0'Ring To design a flanged head without any groove, replace CAG by CSG Without flanged head 0'Ring

FLANGED HEAD SOCKET WELDING (SWI) ISO 6162-2 - S.A.E. 6000
Part N°	DN	Outer diameter tube			Ø L1	Ø L2	Ø A	K	Ø C	L
Part N°	DN	MM	GAZ	SCHD	Ø L1	Ø L2	Ø A	K	Ø C	L
CAG-6000-SWI-1/2"-20.5 CAG-6000-SWI-1/2"-21.7 CAG-6000-SWI-1/2"-22.5	13	20 22	21.25	21.34	20.5 21.7 22.5	32 32 32	13 13 13	13 13 13	32 32 32	60 60 60
CAG-6000-SWI-3/4"-25.7 CAG-6000-SWI-3/4"-27.3 CAG-6000-SWI-3/4"-28.7	19	25 28	26.75	26.68	25.7 27.3 28.7	40 40 40	17.5 17.5 17.5	13 13 13	41.6 41.6 41.6	68 68 68
CAG-6000-SWI-1"-34 CAG-6000-SWI-1"-35.5	25	35	33.50	33.40	34 35.5	48 48	22 22	16 16	47.9 47.9	75 75
* SWI flanges head may only be fitted with split-flanges (the shoulder does not allow a one piece fitting to pass through). These references design groove flanged head for 0'Ring To design a flanged head without any groove, replace CAG by CSG Without flanged head 0'Ring

FLANGED HEAD BUTT WELDING (BWI) - SAE 3000 / SAE 6000 - PN250 / PN400

REDUCING FLANGED HEAD BUTT WELDING (BWR) - SAE 3000 / SAE 6000 - PN250 / PN400

REDUCING FLANGED HEAD SOCKET WELDING (SWR) - SAE 3000 / SAE 6000 - PN250 / PN400

Collets socket welding a passage reduit SWR

REDUCING FLANGED HEAD SOCKET WELDING (SWR) S.A.E. 3000 - CETOP / 250
Part N°	DN	Outer diameter tube			Ø A	Ø C	Ø L1	Ø L2	K	L
Part N°	DN	MM	GAZ	SCHD	Ø A	Ø C	Ø L1	Ø L2	K	L
CAG-250-3000-SWR-1/2"-16.3 CAG-250-3000-SWR-1/2"-17.6	13	16	16.75	17.14	12 12	30.5 30.5	16.3 17.6	24 24	12 12	35 35
CAG-250-3000-SWR-3/4"-18.5 CAG-250-3000-SWR-3/4"-20.5	19	18 20			13 13	38.4 38.4	18.5 20.5	31.5 31.5	13 13	40 40
CAG-250-3000-SWR-3/4"-21.7	19		21.25	21.34	13	38.4	21.7	31.5	13	40
CAG-250-3000-SWR-1"-25.5 CAG-250-3000-SWR-1"-27.3	25	25	26.75	26.68	19 19	44.7 44.7	25.5 27.3	38. 38	14 14	45 45
CAG-250-3000-SWR-1"1/4-30.5 CAG-250-3000-SWR-1"1/4-32.5 CAG-250-3000-SWR-1"1/4-34	32	30 32	33.50	33.40	25 25 25	51.1 51.1 51.1	30.5 32.5 34	43 43 43	16 16 16	50 50 50
CAG-250-3000-SWR-1"1/4-35.5	32	35			25	51.1	35.5	43	16	50
CAG-250-3000-SWR-1"1/2-38.5 CAG-250-3000-SWR-1"1/2-40.5 CAG-250-3000-SWR-1"1/2-43	38	38 40 42	42.25	42.16	32 32 32	60.6 60.6 60.6	38.5 40.5 43	50 50 50	18 18 18	55 55 55
CAG-250-3000-SWR-2"-49 CAG-250-3000-SWR-2"-50.7	51	50	48.25	48.26	38 38	71.4 71.4	49 50.7	61.8 61.8	20 20	65 65
CAG-3000-SWR-2"1/2-61 CAG-3000-SWR-2"1/2-65.8 CAG-250-SWR-2"1/2-61 CAG-250-SWR-2"1/2-65.8	64	60 65 60 65	60.30 60.30	60.32	47 47 47 47	84.1 84.1 87.2 87.2	61 65.8 61 65.8	73.8 73.8 76 76	22 22 22 22	75 75 75 75
CAG-250-3000-SWR-3"-74 CAG-250-3000-SWR-3"-77 CAG-250-3000-SWR-3"-81	76	80	76.10	73.02	58 58 58	101.6 101.6 101.6	74 77 81	90 90 90	24 24 24	85 85 85
Reduced passage means a reduced diameter at the pipe compared with the flange head, materialized by Ø C. Without flanged head 0'Ring These references design groove flanged head for 0'Ring To design a flanged head without any groove, replace CAG by CSG

REDUCING FLANGED HEAD SOCKET WELDING (SWR) S.A.E. 6000 - CETOP / 400
Part N°	DN	Outer diameter tube			Ø A	Ø C	Ø L1	Ø L2	K	L
Part N°	DN	MM	GAZ	SCHD	Ø A	Ø C	Ø L1	Ø L2	K	L
CAG-400-6000-SWR-1/2"-16.3 CAG-400-6000-SWR-1/2"-17.6	13	16	16.75	17.14	11 11	32 32	16.3 17.6	24 24	13 13	35 35
CAG-6000-SWR-3/4"-18.5	19	18			13	41.6	18.5	31.8	13	40
CAG-400-SWR-3/4"-18.5		18			13	39.5	18.5	31.8	13	40
CAG-6000-SWR-3/4"-20.5		20			13	41.6	20.5	31.8	13	40
CAG-400-SWR-3/4"-20.5		20			13	39.5	20.5	31.8	13	40
CAG-6000-SWR-3/4"-21.7			21.15	21.34	13	41.6	21.7	31.8	13	40
CAG-400-SWR-3/4"-21.7			21.25	21.34	13	39.5	21.7	31.8	13	40
CAG-400-6000-SWR-1"-25.5 CAG-400-6000-SWR-1"-27.3	25	25	26.75	26.68	17.5 17.5	47.9 47.9	25.5 27.3	38 38	13 13	45 45
CAG-400-6000-SWR-1"1/4-30.5	32	30			22	54.3	30.5	44	16	50
CAG-400-6000-SWR-1"1/4-32.5		32			22	54.3	32.5	44	16	50
CAG-400-6000-SWR-1"1/4-34			33.50	33.40	22	54.3	34	44	16	50
CAG-400-6000-SWR-1"1/4-35.5		35			22	54.3	35.5	44	16	50
CAG-400-6000-SWR-1"1/2-38.5 CAG-400-6000-SWR-1"1/2-40.5 CAG-400-6000-SWR-1"1/2-42.8	38	38 40 42	42.25	42.16	29 29 29	63.8 63.8 63.8	38.5 40.5 42.8	51 51 51	18 18 18	55 55 55
CAG-400-6000-SWR-2"49	51	50	48.25	48.26	35	79.4	49	67	20	65
CAG-400-6000-SWR-2"50.8	51	50			35	79.4	50.8	67	20	65
Reduced passage means a reduced diameter at the pipe compared with the flange head, materialized by Ø C. Without flanged head 0'Ring These references design groove flanged head for 0'Ring To design a flanged head without any groove, replace CAG by CSG

Adaptors

Flanges Plug

Threaded Flanged Head

THREADED FLANGED HEAD BSPP - SAE 3000 / SAE 6000 - PN250 / PN400

THREADED FLANGED HEAD BSPP S.A.E. 3000 - CETOP / 250
Part N°	PN bar1	DN	Ø F.BSP cyl.	Ø A	Ø C	L	S
CAG-3000-F-G-CYL-1/2"-A * CAG-250-3000-F-G-CYL-1/2"-B	300	13 13	1/2" 3/8"	11 9	30.5 30.5	50 50	21 19
CAG-250-3000-F-G-CYL-3/4"-A CAG-250-3000-F-G-CYL-3/4"-B		19 19	3/4" 1/2	17 11	38.4 38.4	60 60	26 26
CAG-250-3000-F-G-CYL-1"-A** CAG-250-3000-F-G-CYL-1"-B		25 25	1" 3/4	22 17	44.7 44.7	65 65	32 32
CAG-3000-F-G-CYL-1"1/4-A * CAG-250-3000-F-G-CYL-1"1/4-B	150	32 32	1"1/4 1"	30 22	51.1 51.1	70 70	41 41
CAG-3000-F-G-CYL-1"1/2-A * CAG-250-3000-F-G-CYL-1"1/2-B		38 38	1"1/2 1"1/4	36 30	60.6 60.6	75 75	50 41
CAG-3000-F-G-CYL-2"-A * CAG-250-3000-F-G-CYL-2"-B		51 51	2" 1"1/2	44 36	71.4 71.4	80 80	55 50
(1)Pressure max. recommended. Male threaded BSPP (ISO 228/NF E 03-005), sealing with ring "BS" or cupper 0'Ring. Without flanged head 0'Ring. These references design groove flanged head for 0'Ring. To design a flanged head without any groove, replace CAG by CSG. ** assembles itself with joint only coppers, for ring BS consult us NOTE : Further to the sealing, some of flanged head can be use only with split flanges, they are indicated into the references by only 3000 or 6000

THREADED FLANGED HEAD BSPP S.A.E. 6000 - CETOP / 400
Part N°	PN bar1	DN	Ø F.BSP cyl.	Ø A	Ø C	L	S
CAG-6000-F-G-CYL-1/2"-A * CAG-400-6000-F-G-CYL-1/2"-B	350	13 13	1/2" 3/8"	10 8	32 32	60 60	21 19
CAG-6000-F-G-CYL-3/4"-A * CAG-6000-F-G-CYL-3/4"-B * CAG-400-F-G-CYL-3/4"-A CAG-400-F-G-CYL-3/4"-B		19 19 19 19	3/4" 1/2" 3/4" 1/2"	16 10 16 10	41.6 41.6 39.5 39.5	60 60 60 60	26 26 26 26
CAG-6000-F-G-CYL-1"-A * CAG-400-6000-F-G-CYL-1"-B		25 25	1" 3/4	20 16	47.9 47.9	70 70	32 32
CAG-6000-F-G-CYL-1"1/4-A * CAG-400-6000-F-G-CYL-1"1/4-B	250	32 32	1"1/4 1"	26 20	54.3 54.3	75 75	41 32
CAG-6000-F-G-CYL-1"1/2-A * CAG-400-6000-F-G-CYL-1"1/2-B	250	38 38	1"1/2 1"1/4	30 26	63.8 63.8	80 80	50 41
CAG-6000-F-G-CYL-2"-A * CAG-400-6000-F-G-CYL-2"-B	200	51 51	2" 1"1/2	40 30	79.4 79.4	90 90	55 55
(1)Pressure max. recommended. Male threaded BSPP (ISO 228/NF E 03-005), sealing with ring "BS" or cupper 0'Ring. Without flanged head 0'Ring. These references design groove flanged head for 0'Ring. To design a flanged head without any groove, replace CAG by CSG. ** assembles itself with joint only coppers, for ring BS consult us NOTE : Further to the sealing, some of flanged head can be use only with split flanges, they are indicated into the references by only 3000 or 6000

THREADED FLANGED HEAD BSP STUD AND NPT - SAE 3000 / SAE 6000 - PN250 / PN400

THREADED FLANGED HEAD DIN 2353 (24°) ISO 8434-1 AND 4
SAE 3000 / SAE 6000 - PN250 / PN400

Collets filetes metriques a cone interieur 24

THREADED FLANGED HEAD DIN 2353 (24°) ISO 8434-1 AND 4 S.A.E. 3000 - CETOP / 250
Part N°	PN bar1	DN	Ø F	Ø D x série	Ø A	Ø C	L	S
CAG-250-3000-F-DIN-1/2"-A CAG-250-3000-F-DIN-1/2"-B CAG-250-3000-F-DIN-1/2"-C CAG-3000-F-DIN-1/2"-D	315	13 13 13 13	M 20X1.5 M 22X1.5 M 24X1.5 M 26X1.5	12 S 15 L 16 S 18 L	8 12 12 14	30.5 30.5 30.5 30.5	50 50 50 50	19 19 19 19
	350
	315
CAG-250-3000-F-DIN-3/4"-A	350	19	M 24X1.5	16 S	12	38.4	55	27
CAG-250-3000-F-DIN-3/4"-B		19	M 30X2	20 S	16	38.4	55	27
CAG-250-3000-F-DIN-3/4"-C	160	19	M 30X2	22 L	18	38.4	55	27
CAG-250-3000-F-DIN-1"-A CAG-250-3000-F-DIN-1"-B CAG-250-3000-F-DIN-1"-C	315	25 25 25	M 30X2 M 36X2 M 36X2	20 S 25 S 28 L	16 20 23	44.7 44.7 44.7	60 60 60	32 32 32
	160
CAG-250-3000-F-DIN-1"1/4-A	250	32	M 36X2	25 S	20	51.1	60	41
CAG-250-3000-F-DIN-1"1/4-B		32	M 42X2	30 S	25	51.1	60	41
CAG-3000-F-DIN-1"1/4-C	160	32	M 45X2	35 L	30	51.1	60	41
CAG-250-3000-F-DIN-1"1/2-A CAG-3000-F-DIN-1"1/2-B CAG-3000-F-DIN-1"1/2-C		38 38 38	M 45X2 M 52X2 M 52X2	35 L 42 L 38 S	30 36 32	60.6 60.6 60.6	65 65 65	46 46 46
	200
Pressure max. recommended. Without flanged head 0'Ring. These references design groove flanged head for 0'Ring. To design a flanged head without any groove, replace CAG by CSG.

THREADED FLANGED HEAD DIN 2353 (24°) ISO 8434-1 AND 4 S.A.E. 3000 - CETOP / 250
Part N°	PN bar1	DN	Ø F	Ø D x série	Ø A	Ø C	L	S
CAG-250-3000-F-DIN-1/2"-A CAG-250-3000-F-DIN-1/2"-B CAG-250-3000-F-DIN-1/2"-C CAG-3000-F-DIN-1/2"-D	315	13 13 13 13	M 20X1.5 M 22X1.5 M 24X1.5 M 26X1.5	12 S 15 L 16 S 18 L	8 12 12 14	30.5 30.5 30.5 30.5	50 50 50 50	19 19 19 19
	350
	315
CAG-250-3000-F-DIN-3/4"-A	350	19	M 24X1.5	16 S	12	38.4	55	27
CAG-250-3000-F-DIN-3/4"-B		19	M 30X2	20 S	16	38.4	55	27
CAG-250-3000-F-DIN-3/4"-C	160	19	M 30X2	22 L	18	38.4	55	27
CAG-250-3000-F-DIN-1"-A CAG-250-3000-F-DIN-1"-B CAG-250-3000-F-DIN-1"-C	315	25 25 25	M 30X2 M 36X2 M 36X2	20 S 25 S 28 L	16 20 23	44.7 44.7 44.7	60 60 60	32 32 32
	160
CAG-250-3000-F-DIN-1"1/4-A	250	32	M 36X2	25 S	20	51.1	60	41
CAG-250-3000-F-DIN-1"1/4-B		32	M 42X2	30 S	25	51.1	60	41
CAG-3000-F-DIN-1"1/4-C	160	32	M 45X2	35 L	30	51.1	60	41
CAG-250-3000-F-DIN-1"1/2-A CAG-3000-F-DIN-1"1/2-B CAG-3000-F-DIN-1"1/2-C		38 38 38	M 45X2 M 52X2 M 52X2	35 L 42 L 38 S	30 36 32	60.6 60.6 60.6	65 65 65	46 46 46
	200
Pressure max. recommended. Without flanged head 0'Ring. These references design groove flanged head for 0'Ring. To design a flanged head without any groove, replace CAG by CSG.

SAE TYPE RECTANGULAR FLANGES AND FLANGED HEAD TO BE WELDED	NORM ISO (NORM AFNOR) NORM U.S.A.	ISO 6162-1 and 2 to 2002 ( NF E 48-055 12/86 ) SAE J 518
CETOP AND SIDERURGIE TYPE SQUARE FLANGES AND FLANGED HEAD TO BE WELDED	AFNOR RECOMMENDATION	NF E 48-054 12/98 CETOP RP 63 H ISO 6164 05/94
METRIC BOLTS AND NUTS	AFNOR DIN U.S.A.	NF EN ISO 4762 12/97 912 According to American standard
0-RINGS	USA AFNOR	SAE J 515 NF T 47 501 04/98

Flanges	Flanges head
Untreated external surfaces Internal face Ra = 6,3 Reaming Ra = 6,3	All external sections Ra = 6.3 Pass Ra = 6,3 Bearing surfaces of seals and grooves Ra = 1,6

LIQUIDS CARRIED	OPERATING TEMPERATURE	MATERIAL
Mineral oils, water diluted with soluble oil	- 30° + 110° C	PERBUNAN
Flammable hydraulic oils, oils at high temperatures	- 20 ° + 200° C	VITON* ELASTOMERE FLUORE

	CETOP or SIDERURGIE type square flanges (Figure 3) (square arrangement of fixing bolts) One piece only
	SAE type rectangular flanges (Fig.1 and 2) (rectangular arrangement of fixing bolts) One piece or in two parts.

Dia. screws	M 6	M 8	M 10	M 12	M 14	M 16	M 18	M 20	M 22	M 24	M 27
Couple Maxi da Nm	1	3,2	7	13	14,9	23	32	45	61	71	110

90° PORT ASSEMBLY FLANGES BUTT WELDING S.A.E. 3000 / ISO 6162-1
Part N°	PN Bar¹	DN	ØH1	ØA	C	Q	O	GG	FF	M	N	L	Bolts
Part N°	PN Bar¹	DN	ØH1	ØA	C	Q	O	GG	FF	M	N	L	Metric	UNC
BFX-90°-3000-BWI-1/2"	350	13	21.6	13	12	38.1	57	17.5	63	17	18	13	M 8	5/16"
BFX-90°-3000-BWI-3/4"	350	19	27.2	19	12	47.6	68	22.3	66	18	22	15	M 10	3/8"
BFX-90°-3000-BWI-1"	315	25	34.5	25	13	52.4	74	26.2	77	19	28	15	M 10	3/8"
BFX-90°-3000-BWI-1"1/4*	250	32	42.8	31	13	58.7	81	30.2	91	22	30	17	M 10 ou M 12*	7/16"
BFX-90°-3000-BWI-1"1/2*	210	38	48.6	38	14	69.8	95	35.7	105	25	36	18	M 12 ou M14*	1/2"
BFX-90°-3000-BWI-2"*	210	51	61	50	15	77.8	105	42.9	110	25	41	18	M 12 ou M 14*	1/2"
on request 2"1/2 1)Pressure max. recommended Flanges with 0'Ring and bolts For metric bolts, add "M" after the reference ; for UNC bolts, add "U". * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

TEST PORT SQUARE FLANGES S.A.E. 3000 – ISO 6162-1
Part N°	PN bar1	DN	Ø A	L	GG	Q	FF	O	Ø V
BM-3000-PRISE-TEST-XX-3/8"-M BM-3000-PRISE-TEST-XX-1/2"-M/U	350	10 13	12 13	22 25	16.5 17.5	35 38.1	40 45	50 54	9 9
BM-3000-PRISE-TEST-XX-3/4"-M/U		19	19	30	22.3	47.6	50	65	11
BM-3000-PRISE-TEST-XX-1"-M/U BM-3000-PRISE-TEST-XX-1"1/4 M ISO ou M/U*	315	25 32	25 32	30 35	26.2 30.2	52.4 58.7	60 75	70 80	11 11 ou 13
	250
BM-3000-PRISE-TEST-XX-1"1/2 M ou U/ISO*	210	38	38	35	35.7	69.8	80	94	13.5 ou 15
BM-3000-PRISE-TEST-XX-2" M ou U/ISO* BM-3000-PRISE-TEST-XX-2"1/2 M ou U/ISO*		51 64	47 58	40 40	42.9 50.8	77.8 88.9	100 110	102 114	13.5 ou 15 13.5 ou 15
	160
BM-3000-PRISE-TEST-XX-3" M/U	138	76	70	45	61.9	106.4	130	135	17
(1)Pressure max. recommended These flange bodies are fitted with pressure inlets with M 10X100 A shape sealed layout - G 1/4 on request - Galvanized-bichromated.

TEST PORT SQUARE FLANGES S.A.E. 6000 – ISO 6162-2
Part N°	PN bar1	DN	Ø A	L	GG	Q	FF	O	Ø V
BM-6000-PRISE-TEST-XX-1/2-M/U BM-6000-PRISE-TEST-XX-3/4"-M/U	400	13 19	13 17.5	25 30	18.2 23.8	40.5 50.8	48 60	56 71	9 11
BM-6000-PRISE-TEST-XX-1"-M/U		25	22	30	27.8	57.2	70	81	12.5
BM-6000-PRISE-TEST-XX-1"1/4-M ou U/ISO* BM-6000-PRISE-TEST-XX-1"1/2-M/U		32 38	29 35	35 35	31.8 36.5	66.6 79.3	78 95	95 113	13.5 ou 15 17
BM-6000-PRISE-TEST-XX-2" M/ U/ISO		51	43	40	44.5	96.8	114	133	21
(1)Pressure max. recommended These flange bodies are fitted with pressure inlets with M 10X100 A shape sealed layout - G 1/4 on request - Galvanized-bichromated.

COUNTER FLANGES SWI (MONOBLOC) S.A.E. 3000 –ISO 6162-1
Part N°	PN bar¹	DN	ØA	ØB	L	GG	Q	FF	U	K	O	Bolts
Part N°	PN bar¹	DN	ØA	ØB	L	GG	Q	FF	U	K	O	Metric	UNC
BAS-MATRI-3000-SWI-1/2"-21.6	345	13	21.6	13	36	17.5	38.1	47	16	18	57	M 8	5/16"
BAS-MATRI-3000-SWI-3/4"-27.2		19	27.2	19	36	22.3	47.6	49	18	18	66	M 10	3/8"
BAS-MATRI-3000-SWI-1"-34		25	34.1	25	38	26.2	52.4	53	18	18	71	M 10	3/8"
BAS-MATRI-3000-SWI-1"1/4-43*	278	32	42.8	31	41	30.2	58.7	69	21	20	80	M 10 ou M 12*	7/16"
BAS-MATRI-3000-SWI-1"1/2-49*	210	38	48.6	38	44	35.7	69.8	77	25	22	94	M 12 ou M 14*	1/2"
BAS-MATRI-3000-SWI-2"-61*	210	51	61	50	45	42.9	77.8	89	25	24	103	M 12 ou M 14 *	1/2"
BAS-MATRI-3000-SWI-2"1/2-77*	175	64	76.6	63	50	50.8	88.9	101	25	28	115	M 12 ou M 14*	1/2"
BAS-MATRI-3000-SWI-3"-90.5	138	76	90.5	73	50	61.9	106.4	124	27	28	135	M 16	5/8"
(1)Pressure max. recommended - DN 3"1/2 and 4" on request For metric bolts, add "M" after the reference ; for UNC bolts, add "U". * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

COUNTER FLANGES SWI (MONOBLOC) S.A.E. 6000 – ISO 6162-2
Part N°	PN bar¹	DN	ØA	ØB	L	GG	Q	FF	U	K	O	Bolts
Part N°	PN bar¹	DN	ØA	ØB	L	GG	Q	FF	U	K	O	Metric	UNC
BAS-MATRI-6000-SWI-1/2"-21.6	400	13	21.6	13	36	18.2	40.5	47	16	18	57	M 8	5/16"
BAS-MATRI-6000-SWI-3/4"-27.2		19	27.2	19	36	23.8	50.8	53	19	20	71	M 10	3/8"
BAS-MATRI-6000-SWI-1"-34		25	34.1	25	44	27.8	57.2	66	24	22	80	M 12	7/16"
(1)Pressure max. recommended - Until 2" on request For metric bolts, add "M" after the reference ; for UNC bolts, add "U". * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

CONTER FLANGES SOCKET WELD TUBE END SAE 3000 – ISO 6162-1
Part N°	GG	O	Q	FF	Ø L1	Ø A	K	U	Bolts
BAS-3000-SWI-1/2"-20.5 BAS-3000-SWI-1/2"-21.7	17.5	54	38.1	45	20.5 21.7	13	13	20	M 8
BAS-3000-SWI-3/4"-25.5 BAS-3000-SWI-3/4"-27.3	22.3	65	47.6	55	25.5 27.3	19	13	20	M 10
BAS-3000-SWI-1"-30.5 BAS-3000-SWI-1"-32.5 BAS-3000-SWI-1"-34 BAS-3000-SWI-1"-35.5	26.2	70	52.4	60	30.5 32.5 34 35.5	25	16	25	M 10
BAS-3000-SWI-1"1/4-38.5 * BAS-3000-SWI-1"1/4-40.5 * BAS-3000-SWI-1"1/4-43 *	30.2	80	58.7	73	38.5 40.5 43	32	18	25	M 12 ou M 10 (ISO)
BAS-3000-SWI-1"1/2-49 * BAS-3000-SWI-1"1/2-50.4 *	35.7	94	69.8	80	49 50.4	38	20	30	M 14 ou M 12 (ISO)
BAS-3000-SWI-2"-61 * BAS-3000-SWI-2"-65.8 *	42.9	100	77.8	97	61 65.8	47	24	40	M 14 ou M 12 (ISO)
BAS-3000-SWI-2"1/2-74 * BAS-3000-SWI-2"1/2-77 * BAS-3000-SWI-2"1/2-81 *	50.8	114	88.9	110	74 77 81	58	24	40	M 14 ou M 12 (ISO)
BAS-3000-SWI-3"-90.5	61.9	135	106.4	131	90.5	70	28	40	M 16
(1)Pressure max. recommended * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

PORT ELBOW S.A.E. 3000 – ISO 6162-1
Part N°	PN Bar1	DN	Ø A	FF	O	D	Q	GG	Screw		Bolts
									Metric	UNC	Metric	UNC
BLC-EQ-FIX-3000-3/8" BLC-EQ-FIX-3000-1/2"	350	10 13	12 13	41 46	52 58	50 56	35 38.1	16.5 17.5	M 8X55 M 8X60	- 5/16"-2"1/4	M 8 M 8	- 5/16"
BLC-EQ-FIX-3000-3/4		19	19	53	66	66	47.6	22.3	M 10X70	3/8"-2"3/4	M 10	3/8"
BLC-EQ-FIX-3000-1" BLC-EQ-FIX-3000-1"1/4 *	315	25 32	25 32	60 75	72 80	80 95	52.4 58.7	26.2 30.2	M 10X75 M 12X90	3/8"-3" 7/16"-3"1/2	M 10 M 12 *	3/8" 7/16"
	250
BLC-EQ-FIX-3000-1"1/2 *	210	38	38	85	95	110	69.8	35.7	M 14X110	1/2"-4"1/2	M 14 *	1/2"
BLC-EQ-FIX-3000-2" * BLC-EQ-FIX-3000-2"1/2 *		51 64	47 58	100 110	108 118	110 125	77.7 88.9	42.9 50.8	M 14X120 M 14X130	1/2"-5" 1/2"-5"	M 14 * M 14 *	1/2" 1/2"
	160
BLC-EQ-FIX-3000-3"	138	76	70	132	138	150	106.4	61.9	M 16X160	5/8"-6"1/2	M 16	5/8"
(1)Pressure max. recommended blocks with 0'Ring and bolts For metric bolts, add "M" after the reference ; for UNC bolts, add "U". * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

PORT ELBOW S.A.E. 6000 – ISO 6162-2
Part N°	PN Bar1	DN	Ø A	FF	O	D	Q	GG	Screw		Bolts
									Metric	UNC	Metric	UNC
BLC-EQ-FIX-6000-1/2" BLC-EQ-FIX-6000-3/4"	400	13 19	13 17.5	50 62	58 73	56 66	40.5 50.8	18.2 23.8	M 8X65 M 10X80	5/16"-2"1/2 3/8"-3"1/4	M 8 M 10	5/16" 3/8"
BLC-EQ-FIX-6000-1"		25	22	72	83	80	57.2	27.8	M 12X90	7/16"-3"1/2	M 12	7/16"
BLC-EQ-FIX-6000-1"1/4 * BLC-EQ-FIX-6000-1"1/2		32 38	29 35	80 98	98 115	95 110	66.6 79.3	31.8 36.5	M 14X100* M 16X120	1/2"-4" 5/8"-5"	M 14 * M 16	1/2" 5/8"
BLC-EQ-FIX-6000-2"		51	43	116	135	135	96.8	44.5	M 20X150	3/4"-6"	M 20	3/4"
(1)Pressure max. recommended Blocks with 0'Ring and bolts For metric bolts, add "M" after the reference ; for UNC bolts, add "U". * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

"L" BLOCKS S.A.E. 3000 – ISO 6162-1
Part N°	PN Bar1	DN	Ø A	O	FF	C	GG	Q	Bolts
									Metric	UNC
BLC-DIST-L-3000-3/8" BLC-DIST-L-3000-1/2"	350	10 13	12 13	52 58	41 46	50 56	16.5 17.5	35 38.1	M 8 M 8	- 5/16"
BLC-DIST-L-3000-3/4"		19	19	66	53	66	22.3	47.6	M 10	3/8"
BLC-DIST-L-3000-1" BLC-DIST-L-3000-1"1/4*	315	25 32	25 32	72 80	60 75	80 95	26.2 30.2	52.4 58.7	M 10 M 12 *	3/8" 7/16"
	250
BLC-DIST-L-3000-1"1/2*	210	38	38	95	85	110	35.7	69.8	M 14 *	1/2"
BLC-DIST-L-3000-2"* BLC-DIST-L-3000-2"1/2*		51 64	47 58	108 118	100 110	110 125	42.9 50.8	77.8 88.9	M 14 * M 14 *	1/2" 1/2"
	160
BLC-DIST-L-3000-3"	138	76	70	138	132	150	61.9	106.4	M 16	5/8"
(1)Pressure max. recommended For metric bolts, add "M" after the reference ; for UNC bolts, add "U". * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

"L" BLOCKS S.A.E. 6000 – ISO 6162-2
Part N°	PN Bar1	DN	Ø A	O	FF	C	GG	Q	Bolts
Part N°	PN Bar1	DN	Ø A	O	FF	C	GG	Q	Metric	UNC
BLC-DIST-L-6000-1/2" BLC-DIST-L-6000-3/4"	400	13 19	13 17.5	58 73	50 62	56 66	18.2 23.8	40.5 50.8	M 8 M 10	5/16" 3/8"
BLC-DIST-L-6000-1"		25	22	83	72	80	27.8	57.2	M 12	7/16"
BLC-DIST-L-6000-1"1/4* BLC-DIST-L-6000-1"1/2		32 38	29 35	98 115	80 98	95 110	31.8 36.5	66.6 79.3	M 14 * M 16	1/2" 5/8"
BLC-DIST-L-6000-2"		51	43	135	116	135	44.5	96.8	M 20	3/4"
(1)Pressure max. recommended For metric bolts, add "M" after the reference ; for UNC bolts, add "U". * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

"T" BLOCKS S.A.E. 3000 – ISO 6162-1
Part N°	PN bar1	DN	Ø A	O	FF	C	GG	Q	Bolts
									Metric	UNC
BLC-DIST-T-3000-3/8" BLC-DIST-T-3000-1/2"	350	10 13	12 13	52 58	41 46	50 56	16.5 17.5	35 38.1	M 8 M 8	- 5/16"
BLC-DIST-T-3000-3/4"		19	19	66	53	66	22.3	47.6	M 10	3/8"
BLC-DIST-T-3000-1" BLC-DIST-T-3000-1"1/4*	315	25 32	25 32	72 80	60 75	80 95	26.2 30.2	52.4 58.7	M 10 M 12 *	3/8" 7/16"
	250
BLC-DIST-T-3000-1"1/2*	210	38	38	95	85	110	35.7	69.8	M 14 *	1/2"
BLC-DIST-T-3000-2"* BLC-DIST-T-3000-2"1/2*		51 64	47 58	108 118	100 110	110 125	42.9 50.8	77.7 88.9	M 14 * M 14 *	1/2" 1/2"
	160
BLC-DIST-T-3000-3"	138	76	70	138	132	150	61.9	106.4	M 16	5/8"
(1)Pressure max. recommended For metric bolts, add "M" after the reference ; for UNC bolts, add "U". * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

"T" BLOCKS S.A.E. 6000 – ISO 6162-2
Part N°	PN bar1	DN	Ø A	O	FF	C	GG	Q	Bolts
Part N°	PN bar1	DN	Ø A	O	FF	C	GG	Q	Metric	UNC
BLC-DIST-T-6000-1/2" BLC-DIST-T-6000-3/4"	400	13 19	13 17.5	58 73	50 62	56 66	18.2 23.8	40.5 50.8	M 8 M 10	5/16" 3/8"
BLC-DIST-T-6000-1"		25	22	83	72	80	27.8	57.2	M 12	7/16"
BLC-DIST-T-6000-1"1/4* BLC-DIST-T-6000-1"1/2		32 38	29 35	98 115	80 98	95 110	31.8 36.5	66.6 79.3	M 14 * M 16	1/2" 5/8"
BLC-DIST-T-6000-2"		51	43	135	116	135	44.5	96.8	M 20	3/4"
(1)Pressure max. recommended For metric bolts, add "M" after the reference ; for UNC bolts, add "U". * On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

"X" BLOCKS S.A.E. 3000 – ISO 6162-1
Part N°	PN bar1	DN	Ø A	O	FF	C	GG	Q	Bolts
									Metric	UNC
BLC-DIST-X-3000-3/8" BLC-DIST-X-3000-1/2"	350	10 13	12 13	52 58	41 46	60 68	16.5 17.5	35 38.1	M 8 M 8	- 5/16"
BLC-DIST-X-3000-3/4"		19	19	66	53	82	22.3	47.6	M 10	3/8"
BLC-DIST-X-3000-1" BLC-DIST-X-3000-1"1/4*	315	25 32	25 32	72 80	60 75	95 110	26.2 30.2	52.4 58.7	M 10 M 12 *	3/8" 7/16"
	250
BLC-DIST-X-3000-1"1/2*	210	38	38	95	85	120	35.7	69.8	M 14 *	1/2"
BLC-DIST-X-3000-2"* BLC-DIST-X-3000-2"1/2*		51 64	47 58	108 118	100 110	120 130	42.9 50.8	77.7 88.9	M 14 * M 14 *	1/2" 1/2"
	160
BLC-DIST-X-3000-3"	138	76	70	138	132	160	61.9	106.4	M 16	5/8"
(1)Pressure max. recommended For metric bolts, add "M" after the reference ; for UNC bolts, add "U". On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

"X" BLOCKS S.A.E. 6000 – ISO 6162-2
Part N°	PN bar1	DN	Ø A	O	FF	C	GG	Q	Bolts
Part N°	PN bar1	DN	Ø A	O	FF	C	GG	Q	Metric	UNC
BLC-DIST-X-6000-1/2" BLC-DIST-X-6000-3/4"	400	13 19	13 17.5	58 73	50 62	68 82	18.2 23.8	40.5 50.8	M 8 M 10	5/16" 3/8"
BLC-DIST-X-6000-1"		25	22	83	72	94	27.8	57.2	M 12	7/16"
BLC-DIST-X-6000-1"1/4* BLC-DIST-X-6000-1"1/2		32 38	29 35	98 115	80 98	110 130	31.8 36.5	66.6 79.3	M 14 * M 16	1/2" 5/8"
BLC-DIST-X-6000-2"		51	43	135	116	140	44.5	96.8	M 20	3/4"
(1)Pressure max. recommended For metric bolts, add "M" after the reference ; for UNC bolts, add "U". On request can be delivered with ISO 6162 bolt : SAE 3000 1"1/4 = M10, 1"1/2 to 2"1/2 = M12 / SAE 6000 1"1/4 = M12. Specify into the order

SQUARE FLANGES CETOP-SIDERURGIE PN 250 / CETOP
Part N°	PN bar¹	DN	O	GG	Ø J	Ø D	U	F	T
BM-250-CET-3/8" BM-250-CET-1/2"	250	10 13	40 45	24.7 29.7	18.5 24.3	25.1 31	14 * 15 *	6.2 6.2	6.5 8.5
BM-250-SID-1/2"		13	45	30	24.3	31	15	6.2	6.5
BM-250-CET-SID-3/4" BM-250-CET-SID-1"		19 25	50 65	35.3 43.8	32.1 38.5	38.9 45.3	16 * 18 *	6.2 7.6	8.5 11
BM-250-CET-SID-1"1/4		32	75	51.6	43.7	51.6	22 *	7.6	13
BM-250-CET-1"1/2 BM-250-SID-1"1/2		38 38	85* 85	60,1 60	50.8 50.8	61.1 61.1	25 * 25	7.6 7.6	15 * 13
BM-250-CET-2"		51	100	69.3	62.7	72.2	30 *	9	17
BM-250-SID-2" BM-250-CET-2"1/2		51 56	100 120	68 83.4	62.7 76.6	72.2 88	30 35 *	9 9	15 21
BM-250-SID-2"1/2		56	120	85	76.6	88	35	9	19
BM-250-CET-3" BM-250-SID-3"		63 63	140 140	102.5 95	90.8 90.8	102.3 102.3	40 * 40	9 9	21 23
BM-250-CET-3"1/2		70	140 *	102.5 *	102.5	120	52 *	17.5	21 *
BM-250-CET-4" BM-250-SID-4"		80 80	160 * 180	113.2 * 130	114.5 114.5	132 132	60 * 60	21 21	21 * 25
(1)Pressure max. recommended On request can be delivered with ISO 6164

SQUARE FLANGES CETOP-SIDERURGIE PN 400 / CETOP
Part N°	PN bar¹	DN	O	GG	Ø J	Ø D	U	F	T
BM-400-CET-3/8" BM-400-CET-1/2"	400	10 13	40 45	24.7 29.7	18.5 24.6	26.5 32.5	16 * 17 *	7.4 7.4	6.5 8.5
BM-400-CET-3/4"		19	50	35.4	32.5	40	20 *	8.4	8.5
BM-400-CET-1" BM-400-CET-1"1/4		25 32	65 75	43.8 51.6	38.5 44.5	48.4 54.8	24 * 28 *	9.1 9.9	11 13
BM-400-CET-1"1/2 *		38	85 *	60,1	51.6	64.3	32 *	12.2	15 *
BM-400-CET-2" BM-400-CET-2"1/2		51 56	100 120	69.3 83.4	67.6 80.5	80.2 95	40 * 45 *	12.2 16.1	17 21
BM-400-CET-3" *		63	140 *	102.5	90.5	105	52 *	16.1	21 *
BM-400-CET-3"1/2 * BM-400-CET-4 *		70 80	140 * 160 *	102.5 * 113.2 *	102.5 114.5	120 132	52 * 60 *	17.5 21	21 * 25 *
(1)Pressure max. recommended On request can be delivered with ISO 6164

PORT ASSEMBLY FLANGES SOCKET WELDING CETOP-SIDERURGIE PN 250* / CETOP
Part N°	PN bar¹	DN	Outer diameter tube			Ø L1	Ø A	K	L	O	GG	Bolts Metric
Part N°	PN bar¹	DN	MM	GAZ	SCHD	Ø L1	Ø A	K	L	O	GG	Bolts Metric
BFX-250-SWI-CET-1/2"-20.5 BFX-250-SWI-CET-1/2"-21.7	250	13	20	21.25	21.34	20.5 21.7	14	13	32	45	29.7	8 X 45
BFX-250-SWI-SID-1/2"-20.5 BFX-250-SWI-SID-1/2"-21.7		13	20	21.25	21.34	20.5 21.7	14	13	32	45	30	6 X 40
BFX-250-SWI-CET-SID-3/4"-25.5		19	25			25.5	19	14	32	50	35.3	8 X 45
BFX-250-SWI-CET-SID-3/4"-27.2		19		26.75	26.68	27.2	19	14	32	50	35.3	8 X 45
BFX-250-SWI-CET-SID-1"-30.5 BFX-250-SWI-CET-SID-1"-32.5 BFX-250-SWI-CET-SID-1"-34.5		25	30 32	33.50	33.40	30.5 32.5 34.5	25	16	36	65	43.8	10 X 50
BFX-250-SWI-CET-SID-1"1/4-38.5			38			38.5
BFX-250-SWI-CET-SID-1"1/4-40.7		32	40			40.7	31	18	38	75	51.6	12 X 60
BFX-250-SWI-CET-SID-1"1/4-42.8			42	42.25	42.16	42.8
BFX-250-SWI-CET-1"1/2-48.6 BFX-250-SWI-CET-1"1/2-50.7		38	50	48.25	48.26	48.6 50.7	38	20	42	85	60	14 X 65
BFX-250-SWI-SID-1"1/2-48.6 BFX-250-SWI-SID-1"1/2-50.7		38	50	48.25	48.26	48.6 50.7	38	20	42	85	60	12 X 65
BFX-250-SWI-CET-2"-61		51	60	60.30	60.32	61	50	22	44	100	69.4	16 X 70
BFX-250-SWI-CET-2"-65.8			64			64					69.4	16 X 70
BFX-250-SWI-SID-2"-61			60			61.0					68	14 X 70
BFX-250-SWI-SID-2"-65.8			64			64					68	14 X 70
BFX-250-SWI-CET-2"1/2-74 BFX-250-SWI-CET-2"1/2-77 BFX-250-SWI-CET-2"1/2-81		56	80	76.10	73.02	74.0 77.0 81.0	63	24	48	120	83.4	20 X 80
BFX-250-SWI-SID-2"1/2-74 BFX-250-SWI-SID-2"1/2-77 BFX-250-SWI-SID-2"1/2-81		56	80	76.10	73.02	74.0 77.0 81.0	63	24	48	120	85	18 X 80
BFX-250-SWI-CET-3"-91		63	90		88.90	91.0	76	28	55	140	102.5	20 X 90
BFX-250-SWI-SID-3"-91		63	90		88.90	91.0	76	28	55	140	95	22 X 90
(1)Pressure max. recommended Flanges with 0'Ring and metric bolts. On request can be delivered with ISO 6164

"T" BLOCKS BW CETOP-SIDERURGIE PN 250* / CETOP
Part N°	PN bar¹	DN	Ø B	D	Ø A	Ø H1	C	O	GG	Bolts Metric
BFX-TE-250-BWI-CET-3/8"	250	10	12	12	12	18	32	40	24.7	6 X 30
BFX-TE-250-BWI-CET-1/2"		13	14	17	15	22	40	45	29.7	8 X 40
BFX-TE-250-BWI-SID-1/2"		13	14	17	15	22	40	45	30	6 X40
BFX-TE-250-BWI-CET-SID-3/4" BFX-TE-250-BWI-CET-SID-1"		19 25	19 23	19 24	20 25	28 35	42 50	50 65	35.3 43.8	8 X 45 10 X 55
BFX-TE-250-BWI-CET-SID-1"1/4		32	30	30	32	44	56	75	51.6	12 X 70
BFX-TE-250-BWI-CET-1"1/2 BFX-TE-250-BWI-SID-1"1/2		38 38	35 35	34 34	38 38	50 50	65 65	85 85	60 60	14 X 80 12 X 80
BFX-TE-250-BWI-CET-2"		51	43	42	47	62	75	100	69.4	16 X 100
BFX-TE-250-BWI-SID-2"		51	43	42	47	62	75	100	68	14 X 100
BFX-TE-250-BWI-CET-2"1/2 BFX-TE-250-BWI-SID-2"1/2		56 56	53 53	53 53	58 58	76 76	85 85	120 120	83.4 85	20 X 120 18 X 120
BFX-TE-250-BWI-CET-3"		63	65	59	70	90	100	140	102.5	20 X 140
BFX-TE-250-BWI-SID-3"		63	65	59	70	90	100	140	95	22 X 140
(1)Pressure max. recommended Flanges with 0'Ring and metric bolts. On request can be delivered with ISO 6164