Hydraulic hoses with wire spiral

In the field of power transmission by hydraulic oil, T532 can convey Skydrol up to 43 bars.
It can also be used for superheated steam up to 18 bars at 232°C.
It is possible to manufacture the ISO 6134-2B certified hose 533 with an oil-resistant outer cover.
Is structure reinforced by metal spirals gives excellent bend radius.
The EPDM rubber ensures long service life.
It meets ISO 6134-2A standards.

Technical specifications :
Inner tube : black EPDM rubber
Reinforcement : metal spirals
Outer cover : black EPDM rubber
Outer finish : fine tape-wrapped
Temperature : - 40°C to +232°C
Production lengths : 40 metres except dias. 19, 25 and 53 : 60 metres
Colour : black with red lay line
Marking : Tecalemit Flexibles - part N° - NFT 47263 - DN (mm/inch) - batch N°

Produced on rigid mandrils from 3/4” up, these hoses are vulcanised in a very long autoclave.
This hose is usually intended for power transmission at high pressures.
It is used in industry, shipping and on earth-moving equipment.
Hoses can be supplied equipped with swaged fittings and test certificates.
It meets the NF EN 856 4SP standard.
The quality of its neoprene outer cover complies with MSHA (Mine Safety and Health Administration) requirements.

Technical specifications :
Inner tube : black synthetic rubber
Reinforcement : 4 steel wire spirals
Outer cover : oil and weather resistant neoprene rubber
Outer finish : wrapped
Temperature : - 40°C to +100°C - peaks to 125°C
Production lengths : 61 metres and variable
Colour : black
Marking : Tecalemit Flexibles - part N° - NF EN 856 4SP - DN (mm/inch) - wp/ps (bars) - batch N°

Produced on rigid mandrils, these hoses are vulcanised in long length autoclaves.
This hose is usually employed for power transmission at high pressures.
T912 is used in industry, shipping and on earth-moving equipment.
It meets NF EN 856 4SH standards.
The quality of its neoprene outer cover complies with MSHA (Mine Safety and Health Administration) requirements.

Technical specifications :
Inner tube : black nitrile rubber
Reinforcement : 4 or 6 metal spirals
Outer cover : oil and weather resistant neoprene rubber
Outer finish : wrapped
Temperature : - 40°C to +100°C - peaks to 125°C
Production lengths : 61 metres
Colour : black
Marking : Tecalemit Flexibles - part N° - NF EN 856 4SH - DN (mm/inch) - wp/ps (bars) - batch N°

Produced on rigid mandrils, these hoses are vulcanised in long length autoclaves.
This highly abrasion resistant hose is normally intended for high pressure delivery.
Thanks to its special synthetic rubber outer cover, it is particularly resistant to abrasion, oils, fuels and atmospheric agents.
T914 is used in industry, shipping and on earth-moving equipment. 
It meets NF EN 856 4SH standards.

Technical specifications :
Inner tube : black nitrile rubber
Reinforcement : 4 or 6 metal spirals
Recouvrement : Special synthetic rubber outer cover resistant to abrasion, oils, fuels and atmospheric agents.
Outer finish : wrapped
Temperature : - 40°C to +100°C - peaks to 125°C
Production lengths : 61 metres
Colour : black
Marking : Tecalemit Flexibles - part N° - NF EN 856 4SH - ANTI ABRASIF - DN (mm et pouce) - wp/ps (bars) - N°Lot

T915 is among the toughest hydraulic hoses of the range.
I is produced on rigid mandrils and vulcanised in straight lengths.
Its working pressure is 420 bars for all diameters.
Swaging of fittings is carried out after internally and externally skiving the hose.
The metal structure of the hose is then perfectly in cohesion with the metal fitting.
The quality of its neoprene outer cover complies with MSHA (Mine Safety and Health Administration) requirements.

Technical specifications :
Inner tube : black nitrile rubber
Reinforcement : 4 high tensile steel spirals up to 1”, 6 high tensile steel spirals from 1”1/4 up
Outer cover : neoprene rubber
Outer finish : wrapped
Temperature : - 40°C to +120°C - peaks to 125°C
Production lengths : 61 metres
Colour : black
Marking : Tecalemit Flexibles - part N° - NF EN 856 R15 - DN (mm/inch) - wp/ps (bars) - batch N°

The T916 hose is intended for hydraulic systems with high pressure peaks, under severe operating conditions, for mining, offshore, perforation, etc ...
The standard version inner tube is suitable for conveying hydraulic fluids based on mineral, glycol and vegetable oils.
Its MSHA approved coating is resistant to severe abrasion, oils, fuels and atmospheric agents.
The textile folds distribute the pressure forces applied to the inner tube.
The steel wires making up the cables are treated against corrosion.
We crimp various types of tips on this pipe: flanges according to various international standards, line-pipe tips, specific tips depending on request.

Technical specifications :
Inner tube : Synthetic rubber
Reinforcement : 4 (5"18 to 1") or 6 (1"1/4 to 3") very high tensile steel spiral
Outer cover : MSHA resistant synthetic rubber
Outer finish : wrapped
Temperature : -40°C to +100°C - peaks to 125°C
Colour : black

Possible end-fittings : Flange, threaded male NPT
Marking : Tecalemit - part n°- MSHA - bar - batch n°

Hose types T961 and T962 are mainly intended for very high pressure waterblasting.
For example, they are used in refineries, sugar mills, paint spray booths in the automotive industry and also for decennial maintenance of engineering works.
Used with water, the safety factor between burst and working pressure is 2.5.
The hose must be internally and externally skived before mounting and swaging of end-fittings.
The metal structure of the hose is then perfectly in cohesion with the metal fitting.

Technical specifications :
Inner tube : black synthetic rubber
Reinforcement : textile layers, 4 steel spiral layers
Outer cover : chloroprene rubber
Outer finish : wrapped
Temperature : - 40°C to +100°C
Production lengths : variable
Colour : black
Marking : Tecalemit Flexibles - part N° - DN (mm/inch) - batch N°

Hose types T961 and T962 are mainly intended for very high pressure waterblasting.
For example, they are used in refineries, sugar mills, paint spray booths in the automotive industry and also for decennial maintenance of engineering works.
Used with water, the safety factor between burst and working pressure is 2.5.
The hose must be internally and externally skived before mounting and swaging of end-fittings.
The metal structure of the hose is then perfectly in cohesion with the metal fitting.

Technical specifications :
Inner tube : black synthetic rubber
Reinforcement : textile layers, 4 steel spiral layers
Outer cover : chloroprene rubber
Outer finish : wrapped
Temperature : - 40°C to +100°C
Production lengths : variable
Colour : black
Marking : Tecalemit Flexibles - part N° - DN (mm/inch) - batch N°

Hose type T1362 is mainly intended for very high pressure waterblasting.
For example, it is used in refineries, sugar mills, paint spray booths in the automotive industry and also for decennial maintenance of engineering works.
Used with water, the safety factor between burst and working pressure is 2.5.
The hose must be internally and externally skived before mounting and swaging of end-fittings.
The metal structure of the hose is then perfectly in cohesion with the metal fitting.

Technical specifications :
Inner tube : black synthetic rubber
Reinforcement : 6 wire spirals
Outer cover : chloroprene rubber
Outer finish : wrapped
Temperature : - 40°C to +100°C
Production lengths : variable
Colour : black
Marking : Tecalemit Flexibles - part N° - DN (mm/inch) - batch N°