Hoses for the navy

Extremely flexible and light, hose M42 is particularly intended for pleasure boats.
It passes easily from engine comparment through bulkheads to exhaust oulet valve.
Yacht racers appreciate its linear mass.
It replies to sae J2006 type R2 (10/2003) standards relative to pleasure boat wet exhausts, which defines burst pressure, admissible elongation, adherence of components, abrasion and aging resistance of the hose, which must resist exhaust gases during 2 minutes without water cooling.

Technical specifications :
Inner tube : smooth black EPDM rubber
Reinforcement : 1 textile plie and 1 spiral
Outer cover : SBR rubber
Outer finish : wrapped and corrugated
Production lengths : 60 meters - 20 meters from dia. 127
Colour : black
Marking : TECALEMIT - PART N° - Ø - SPECIAL ECHAPPEMENT - MARINE WET EXHAUST - SAE J2006 - BATCH N° - DATE

Intended for supply of fuel to marine engines on pleasure craft, hose 407 corresponds to the international standard ISO 7840 type A1.
This rating defines the inner tube’s lowest permeability to fuels according to that standard.
The quality of the outer cover protects the hose from projections within the engine compartment.
Swaged with end-fittings, this hose can be supplied “ready-to-use”.

Technical specifications :
Inner tube : NBR rubber, resistant to hydrocarbons
Reinforcement : textile braid
Outer cover : CR rubber
Outer finish : smooth
Temperature : - 30°C to +70°C maximum
Production lengths : 40 metres
Colour : black
Marking : TECALEMIT - PART N°- NF EN ISO 7840 - TYPE A1 - LOT - Ø - 1 MPA - PRODUCTION DATE - BATCH N°

Possible end-fittings : Male or female threaded
See also 362, 441

Designed for the suction and discharge of hydrocarbons, hose 493 has a textile reinforcement and a metal spiral.
It is a very robust suction hose.
It can be used in a wide temperature range and its neoprene outer cover provides excellent resistance to ozone and is fireproof.
it is used in discharge when a small bend radius is necessary.

Technical specifications :
Inner tube : NBR rubber
Reinforcement : 1 textile braidand 1 metal spiral
Outer cover : CR fireproof
Outer finish : wrapped
Temperature : - 40° to + 80° c
Production lengths : 61 meters
Colour : black
Marking : Tecalemit - NF EN ISO 7840 - Type A2 - 1MPA - Remplissage reservoir - 2” 1/8 - production date - batch N°

Designed specifically for pleasure boats, hose 817 has a butyl rubber inner tube which has the best impermeability to gasses in the range of elastomers.
Consequently, it is destined to connect effluent circuits on yachts.
With its smooth finish, it has an excellent bend radius allowing different types of mounting inside confined cockpits.
Its white colour allows easy incorporation into sanitary environments.

Technical specifications :
Inner tube : white butyl (IIR) rubber
Reinforcement : 2 textile layers and 1 metal spiral
Outer cover : EPDM rubber
Outer finish : smooth wrapped
Temperature : -30°C to +70°C
Production lengths : 20 meters
Colour : white
Marking : TECALEMIT FLEXIBLES BY SEL - REF 817 - 5 BAR – BATCH N°

This PVC hose is used for the discharge of wastewater.
It is also appreciated for its excellent flexibility.
The pressures indicated in the table are given at 20 °C.

Technical specifications :
Inner tube : flexible PVC
Reinforcement : steel helix
Outer cover : flexible PVC
Outer finish : slightly corrugated
Temperature : - 5°C to +60°C
Production lengths : 30 meters
Colour : white
Marking : none

MANUCLAIR® braided pvc tubes are comprised of a flexible translucent pvc inner tube (abbreviation of soft polyvinyl chloride), a single braid of white polyester yarn and a flexible PVC coating.
The inner tube is obtained by extrusion.
It is then cooled before passing through a vertical braider and an angle extrusion head which deposits the outer cover.
MANUCLAIR® tubes are :
- Food quality.
- Translucent rendering the conveyed product visible.
- Flexible.
- Resistant to many common products.
Even though they are less flexible, less sturdy and accept lower working temperatures than their rubber counterparts, MANULEF® tubes are universally used for their main qualities : food compatibility, translucent aspect and resistance to many fluids.

Technical specifications :
Reinforcement : Translucent PVC
Renforcement : 1 textile braid
Outer covert : Translucent PVC
Outer finish : smooth
Temperature : 0° to + 60° c
Production lengths : 25 metres
Marking : Tecalemit flexibles - Manuclair – D.Int. x D. Ext. - PS/WP 20 BARS 23° - batch N° – Alimentaire